--On Monday, December 31, 2001 08:30:03 -0500 Dan Hoehnen ... This sounds right to me. The 24hr is usually a N/C (normally closed) switch which links to a...
In my new Comfort/HomeVision/PC setup I want to be able to intelligently switch lights on/off and dim depending on movement/occupancy, time of day and light...
Alarm cable is normally multistranded 4 or 6 core wire. CAT 5 is UTP (Unshielded twisted Pair) with 4 twisted pairs. In fact, CAT 5 is recommended for Comfort...
Oops, sorry for confusing the issue. I forgot that unshielded cable was not recommended on the comfort site. I was responding to the comparison between alarm ...
...so with a retro-fit whole-house re-wire, would you recommend CAT 5 or alarm cable for the keypads? I was thinking it would be easier and more flexible just...
Certainly it's a good idea to do some small scale testing before a large scale investment but I have successfully set up Comfort to do the following: Turn on...
1237
Lyndsay Cotton
cotton@...
Jan 3, 2002 1:02 am
I now have 8 lights automated in my home 2 for external lights and 6 for internal The external lights come on for fixed times IRRESPECTIVE of the security ...
1238
Lyndsay Cotton
cotton@...
Jan 3, 2002 1:02 am
Here's a big spanner in the works>>>> I agree, CAT is better, but I've installed many systems and seldom use CAT 5 and I use between 3 and 8 keypads per system...
I understand from the diagram that the two N/C connectors in the PIR should be shorted together with a 4k resistor. The Z3 from comfort should then go to one...
1240
Rod Stephens
rodsteph@...
Jan 3, 2002 2:52 am
In regard to the light level, I have used an external X-10 flood light. You can adjust the light level so it sends a command to Comfort when it gets dark and...
That is correct. Essentially a single route with 2K7 resistor measured at alarm panel means the zone is functional...If the NC terminals open when a body...
Andrew, Question on compatibility of CSXpress v3.22 with my older v3.18. Should I download the UK/Europe version of CSXpress v3.22 or the USA/Rest of World...
1. I have connected a 4 month old master panel with 'outside' firmware , with one year old 3 regular firmware slave panels to receive a total of 64 zones. ...
Mete Check in csxpress Modules that you do not have LEM03 (24 zones) ticked. This will prevent operation with Slaves (SEM) If LEM03 is not ticked, it could be...
i have wired my panel in as shown in the manual. i can dial in from a home phone or remotely. i can use my master socket (though this causes a phone trouble as...
Nothing is wrong, that is the standard behaviour. During Dial Test, you cannot hear the dial tone, as the monitoring is not turned on yet at that point. Is ...
thanks chiu. the problem that i forgot to mention in my email is that it doesnt connect to my mobile numbers. i have 2 numbers programmed, and they are not...
Andrew, I installed CSXpress 3.22 (UK version), but cannot get it to communicate with the Comfort Panel. I get an "Invalid Login" when I attempt to connect or...
1252
Eamon O'Gorman
eamonogorman@...
Jan 6, 2002 2:50 am
Apologies to all, have updated my virus checker (new PC, only a day old and managed to get infected already).. Eamon ... From: "Campbell Macdonald"...
You mean that during dial test, you can hear the numbers getting dialled, but cannot hear the ringback tone? This means that Comfort is doing the dialout. ...
The new install usually sets the COM Port to blank. Go to Options -> Communications port to check this. chiu ... ===== Cytech Technology Pte Ltd 55 Ubi Ave 1...
If you read these group messages in a browser, how can anyone "catch" a virus? Sending an email direct to someone with an attachment that is then opened, that...
