Thanks for that, I am a beginner in the Comfort programming world,and any advice on the pgroamming through CSExpress would be greatful. I take it I program...
... David, Responses are not monitored just because they are in the Responses screen. Only when they are assigned to a trigger event such as , zone, Alarm...
Right, I think I’m beginning to grasp it. Is there a way of adding a new voice command so that when it rings me it actually says ‘Garage open’. Also I am...
Instaed of activating an Alarm, you could activate a Reminder using action 97, reminder#. this will ring your internal phones, when you answer it will play the...
David The siren could be sounding because of the tamper input left open. The SRN+/SRN- should be at 0V in normal circumstances, unless Siren Reverse is set to...
Right tried out the programming last night, I shall just run through what I did to make sure I did it correctly. Programmed Zone 8 (Light sensor) Off Response:...
Your programming is correct It looks like your alarm type 14 has an alarm state 2 (alert) or Alarm (3) whcih causes the red light to flash when the alarm is...
I replied to this is a previous post http://groups.yahoo.com/group/comfort-technical/message/1584, I dont know if this will help chiu ... stopped the siren...
1589
Andrew Brockhurst
andy@...
Apr 4, 2002 9:10 am
Hi, I ordered a UCM to go into my Comfort System a while ago, and got round to fitting it yesterday. No dice. location 1672 was set to 1 already. ld9 & 10 not...
Andy, Are you sure the UCM isn't mounted in the Comfort panel 'without' the pillars, this will short out and possibly damage the PCB. UCM faults are VERY rare....
1591
Andrew Brockhurst
andy@...
Apr 4, 2002 10:03 am
Andrew It's mounted in a separate UniBox, pillars and all. Using CAT5e between the Unibox and Comfort. Continuity tested from the blue connectors. On the UCM...
The U1 IC may not be seated properly or some pin may be deformed. Can you remove it gently with an extraction tool, check for bent pins, and reinsert it, ...
... The Doorbell cadence is different already, but is not adjustable. ... Certain Alarms Dialouts are dependent on Mode (ones associated with Zone Types), but...
... No, it is only possible to apply the ringing voltage to the internal phones, the phones themselves produce whatever ringing tone by their internal...
I've just received an XM10E for use with my Comfort system. Rather stupidly, I forgot to order the RJ11 cable at the same time (and I'd rather not incur...
Hi, Having a problem with the alert for the garage door being open. It does not inform me when it gets dark, if I go out there and shine a touch on the sensor...
Shaun, there is a picture of the cable in the Installation Manual./ Andrew CHC ... Andrew Roberts Comfort Home Controls - UK (Tel: 44(0)1244 680675) (Fax:...
David It looks like there is not enough light in normal daylight for the light sensor to trigger the zone, ie the zone always sees a closed circuit, so the Off...
Just a thought. Reading page 42 of the comfort installation manual is it states that outside PIR's and Photocells require a normally open zone type. I think my...
I have checked this, and this morning the Led on the unit was off, went outside and covered the sensor it went on. So during the day the LED is off, then in...
Yes, this would explain it. The LSM output is normally open, so you should set the zone to Normally Open switch (Zone type 8?). For Normally Open switches, the...
I hope that zone change does work but will be surprised if it does. We used to use another manufacturer's photocell relay before Cytech designed one and that...
Is it ok to extend the RJ11 cable connection between the UCM/Smafit and the Honeywell Smartfit control box , to over 6 meters ( any technical limitations or...
