My system was armed to Night Mode last night. At around 1 am I had a series of beeps from the sounder in the hall and the two LEDs either side of the "Armed"...
308
L Y Chiu
chiu@...
Mar 1, 2001 1:08 pm
Mark It would be the Low battery Alarm if your system has been running on batteries for so long You had better disconnect the battery and let Comfort shut down...
309
Mark McCall
mark@...
Mar 1, 2001 5:43 pm
... My power was restored yesterday morning at 10:00am Chiu so this happened while the system was back on MAINS power. ... I was getting this just before the...
310
Lyndsay Cotton
cotton@...
Mar 1, 2001 6:42 pm
RE: The alarm sounding after approx 24 hours after a power restore I agree. I had an installation a few months back where I cut the power to do some work on...
311
L Y Chiu
chiu@...
Mar 2, 2001 12:46 am
There is an automatic Battery test which turns off the mains power for a few minutes to check the condition of the battery. If the battery voltage is found to...
312
chiu@...
Mar 2, 2001 6:49 am
Try this response example programmed to Zone Response On Response 85,1 stop Timer 1 132,1,2 check Flag 1 13 Exit if Not zero, ie if flag 1...
313
Mark McCall
mark@...
Mar 2, 2001 9:15 am
Thanks Chiu It didn't happen last night so hopefully the cells are back up to their proper level. M. ... From: "L Y Chiu" <chiu@...> To:...
314
Campbell
c.macd@...
Mar 7, 2001 10:12 pm
I have Comfort set up to dial my mobile should somebody press the doorstation when in away mode. Additionally I have 3 outside zones which carry out responses...
315
rmathias@...
Mar 8, 2001 8:04 pm
Hi Another question: How do I adjust the doorphone so that the switch over to the doorphone is faster? The problem is that when I answer the doorphone, the...
316
rmathias@...
Mar 8, 2001 8:05 pm
Hi Andrew / Chiu My system is set up pretty much according to the ISDN example application 1.14. Could you help me figure out how to get Comfort to dial...
317
andrew@...
Mar 8, 2001 8:12 pm
... Robert, You need to save Tel 1 and 2 for Central Station. So try using Tel 5 and 6. Using the Arm and Disarm Alarm types. You don't need to use action 88...
318
L Y Chiu
chiu@...
Mar 9, 2001 6:36 am
The switching time unfortunately cannot be reduced at present. The switching time is a compromise between speed and other factors affecting the performance of ...
319
L Y Chiu
chiu@...
Mar 9, 2001 2:14 pm
Campbell ... does it not dial at all or is the dial delayed because of the announcement ... I assume you have programmed the door station to take a message if...
320
Campbell
c.macd@...
Mar 9, 2001 10:16 pm
Chiu, Thank you for your replies, In response, 1 If the outside zone is activated it will not dial at all in some cases. I think this may be due to...
321
L Y Chiu
chiu@...
Mar 10, 2001 4:05 am
Campbell ... You mean that if the outside detector is triggered after the doorbell is pressed that the dial out does not happen? What is your version? I would...
322
Martin Stevens
martin_stevens@...
Mar 11, 2001 6:57 pm
I have been having problems with my telephones since installing my Comfort system in September. When I connect the house phones to the TEL OUT connector, the...
323
L Y Chiu
chiu@...
Mar 12, 2001 1:49 am
Sorry if you have posted a message without a reply, we may have missed seeing it. When you connect your phones to TEL out and the phone line to TEL In and...
324
Lorenz, Joseph
joe.lorenz@...
Mar 12, 2001 5:21 am
I am curios what Touch Screens people have successfully used with Comfort. I sold a Comfort unit to a very nice chap early last year. Now the Gent is ready to...
325
Lorenz, Joseph
joe.lorenz@...
Mar 12, 2001 5:21 am
I am working w/ a person of interest that would like to incorporate the outside temperature into Comfort. We are working on a configuration to fully automate...
326
L Y Chiu
chiu@...
Mar 12, 2001 3:04 pm
Joe We have been wanting to interface to a communicating thermostat via RS232 for some time. One new version of the UCM that we are developing will have the...
327
chiu@...
Mar 12, 2001 3:12 pm
Joe We have successfuly interfaced to the Leopard touchscreen (www.appdig.com/leopardpreviw.html) via the Rs232 interface. This device has an Rs232 interface...
328
Lorenz, Joseph
joe.lorenz@...
Mar 13, 2001 8:25 am
Chiu, There is a new product from RSC www.resconsys.com. I believe JDS has a similar (OEMed?) version too. Their new product is the Rs-232 thermostat I talked...
329
L Y Chiu
chiu@...
Mar 13, 2001 9:46 am
... We have the RCS RS232 and X10 thermostat ... The new UCM is being tested. It is the old UCM with different firmware which leaves out the STX start ...
330
emyrgeorge@...
Mar 13, 2001 12:34 pm
I want to monitor the performance of a perimeter detector i.e to have it logged but not announced nor alarmed. I am not sure whether I should use zone type 17...
331
comfort@...
Mar 13, 2001 12:41 pm
... I was also thinking about something like this, but for an indoor thermostat. I didn't pursue it in the end, but what I thought of doing was building an...
332
Andrew Roberts - Comf...
andrew@...
Mar 13, 2001 12:54 pm
Emyr, dont use Zone Type 24 for this it has no alarm functions. Try the soak test zone type and make sure it isn't set to dial out. Andrew Roberts Comfort Home...
333
Andrew Roberts - Comf...
andrew@...
Mar 13, 2001 2:25 pm
Visonic Announcement - Frequency changes FROM APRIL 2001, ALL VISONIC POWERCODE PRODUCTS WILL ONLY BE AVAILABLE IN 433MHz SO IF YOU NEED ANY COMPATIBLE 418MHz...
334
Linas Zebelys
pro.s@...
Mar 13, 2001 4:27 pm
Dear sirs, does anyone know, how to change thermostats OTE-10 that was from Quellet. The building is wired for them. Regards, Linas Zebelys...
335
Campbell
c.macd@...
Mar 13, 2001 10:32 pm
If I recall correctly somebody played with this idea previously (Ray I think). I was also interested, but I believe he had problems getting a Farenheit chip...
336
Andy Hall
andyh@...
Mar 15, 2001 12:40 am
Chiu I sent you a mail a while back suggesting that it would make sense to implement a system of "send-expect" sequences and to then do actions based on the...
