Mindaugas I am sure the Time Programs are not inherently unstable. However we have the LSM01 Light sensor module you can consider as an alternative (see ...
Having now programmed the KT01 I note the following: - The status icons do not appear to work ( I tried arming to away and night mode also disconnecting the...
I notice that the responses in 'Events zone inputs' are not sorted alphabetically! I did not check ALL the other response screens Regards Andrew Ellis ...
Problem Mains power cut - comfort alarm is activated the bellbox sounder goes off (not the internal sounders) and stays on (even after the 20min time out)...
When 'executing' a response in control menu I have the following situation: - Response 123 - single Do response CBUS on off command Response 321 - multiple Do...
This appears to the last post on the subject - do I take it that this will occur in the next release 1.7? Regards Andrew Ellis Household Automation - The...
OK like I say I am aware that I am pushing the limit of programming here and I accept them. However 1 - This code was working fine in one down load and then...
Go to engineer menu 8,6,2 Regards Andrew Ellis Household Automation - The synergy of technology and living. M: 07879 401075 T: 0870 3300071 F: 0870 3300072 ...
6468
rid
rid@...
Aug 1, 2005 9:47 pm
Andrew I think this has been covered on several other mailing. I certainly saw it about a year or so ago, worked out what was happening, and learned to code...
Andrew Is your 6 way cable connected to P3 or P4? If you are programming the KT01, it should be connected to P4, else, in normal operations, it should be...
It requires a firmware change, not a comfigurator software change. This old functionality will be reinstated in the next firmware release, ie require responses...
Thats probably the type of self actuating bellbox which requires the mains supply in order to prevent the siren from coming on, not a faulty bellbox chiu ... ...
If you click the drop down box, the names of the responses are displayed in the small drop down window If you want to see the Responses in a larger window,...
OK yes this is a nice feature well done - however you miss the point. As a default surely all the responses in the pull down menus should be initially sorted...
Andy Its true, it is sorted by number, while others are alphabetical, which I did not notice However, the right click method is so superior to the drop down...
OK I have mentioned this topic before and I thought that we had agreement that they would all be sorted alphabetically. (it apears that a majority of the...
The S12V on the SEP - we added a smoke sensor to a zone on an SEP last week (old installation SEP version first 4.164) The S12V did NOT break with the Aux...
I note that there is now an RJ11 socket on the SEP board can you give any indication as to when the X10 function will be available on the SEP? Regards Andrew...
It appears that omitted zones are re-enabled when the system is armed or disarmed. Is this true and is there a way around it. I have my garage door controlled...
Hi, I had my alarm go off twice over the weekend and I'm not sure if it's a false alarm or not. The zone that was triggered has 3 reed contacts and 3 ...
It is not possible to find out which contact wired in series in a zone caused an alarm. It is good practice not to use diferent types of alrm sensors in the ...
Omitted zones remain so even when the system is armed or disarmed. Bypassed zones become enabled when the system is disarmed. You can bypass in the F1 menu or...
We had this working in the lab, ie X10 on Slave, but have not enabled this in the firmware. This will cause any X10 signal which is transmitted from Comfort to...
Yes, the SEMs all should be able to activate the S12V using the action code, exceot for a smal number a few years ago ... Cytech Technology Pte Ltd 55 Ubi Ave...
We find X10 the most useful in 'remote' installations such as garages shed and outbuildings these are the exact situations where we may locate a SEP unit! We...
If the 2 x10 signals were completely seperate, ie on different phases or far way enough without the possibiity of interfering with each other, then there would...
Hi I would like to connect the gate movement detector (used as a safety device with my electric gates) so that Comfort can annouce the zone when somebody...
Can I enable a time program from a response? .... I am setting up an irrigation system that has a control menu response "auto water on", "auto water off" I...
