Hi, It is my intention to construct an 8 way mains relay board. Each relay requires 30mA I am assuming i can connect the coils direct to comfort outputs. Do i...
683
L.Y. Chiu
chiu@...
Aug 1, 2001 12:58 pm
You can connect the coil directly to Comfort outputs if they are 12V dc operated The Comfort outputs have a reverse diode protection so it is not necessary to...
684
L Y Chiu
chiu@...
Aug 2, 2001 2:53 am
Some other settings may have been changed inadvertently In your csx file, check the siren types screen for Siren Type 3, Arming Tone and check that the sound ...
685
idheath@...
Aug 2, 2001 7:36 pm
I've been having some problems with a zone so I've put it on Soak Test. But this seems to be causing some strange results. If the Zone is activated whilst the...
686
Steve Gordon
steve@...
Aug 3, 2001 1:06 am
Chiu, Thanks for the response. Is there a hardware change required to impalement the new IR equipment? My guess is yes (Especially the eeprom bit) ,but I don't...
687
Andrew Roberts - Comf...
andrew@...
Aug 3, 2001 8:27 am
Steve, I think that there will be a firmware change to add the new IR functionality and also the IR modules themselves, which may be retrofitted, so this will ...
688
Ian Heath
idheath@...
Aug 3, 2001 8:46 am
Andrew, Thanks for your response, .....but if I change the Soak Test Alarm State to Alert will it cause problems if their is a another trigger within 10...
689
comforttechnical.csc1...
Aug 3, 2001 9:36 am
Hi I'm not a newbie - I have paid for an installer to do my work, but after several months, it still isn't done...I don't WANT to learn how to use comfort, but...
690
Ian Heath
idheath@...
Aug 3, 2001 9:39 am
Thanks, I think it's time to upgrade!! What's the best version to go for (Outside version?!)? I want to be as future proof as possible, but in the short term...
691
comforttechnical.csc1...
Aug 3, 2001 10:32 am
... how ... help on the situation there. ... Andrew I'd prefer to use CSExpress to permentatly remove it. As for the IR - the installer has said they cant get...
692
L Y Chiu
chiu@...
Aug 3, 2001 10:49 am
Steve You should not need to change any hardware for the new ir functionality. You will need a U1 upgrade. If the New EEPROM becomes available it can fit into...
693
Andrew Roberts - Comf...
andrew@...
Aug 3, 2001 10:58 am
Gareth, I still dont know what IR you are referring to? There are numerous possibilities Andrew Roberts Comfort Home Controls - UK (Tel: 44(0)1244 680675) ...
694
steve
steve@...
Aug 4, 2001 1:05 am
Should i use for 8 relays - 16 wires or can i do it with 9 using a common ? Steve. ... From: L.Y. Chiu To: comfort-technical@yahoogroups.com Sent: Wednesday,...
695
comforttechnical.csc1...
Aug 4, 2001 1:05 am
This little fella. http://www.comfort.org.uk/images/IRM01_BIG.jpg ... but ... learn ... way to ... be ... connections... ... like ... reset. ... good. ... up ....
696
L Y Chiu
chiu@...
Aug 4, 2001 1:14 am
Ian I think only Outside versions are now available in the UK If you use csx 2.x you will not be able to program - x10 received responses - IR received...
697
L Y Chiu
chiu@...
Aug 4, 2001 1:21 am
To connect the 8 relays to Comfort outputs, you can use 8 + common (12V) chiu ... ===== Cytech Technology Pte Ltd 55 Ubi Ave 1 #04-06, Singapore 408935 Tel...
698
L Y Chiu
chiu@...
Aug 4, 2001 9:19 am
I am not sure how the Soak test is implemented in this case. If it a zone type, the behaviour is completely defined by how it is set in csxpress Or you can use...
699
john.engelhardt@...
Aug 5, 2001 11:01 am
Tech Support Forum: I have a very strange problem going on with my system: SYSTEM SPECS: + 48 zones (about 20 used) with 2 SEP01 and 1 Main CPU + 6 Kompads...
700
L Y Chiu
chiu@...
Aug 5, 2001 2:00 pm
It looks like there is no 12V getting to KP #2 to 6 and the Door stations. This seems to be confirmed by the fact that the sensors, glassbreak which require ...
701
Vince
vince@...
Aug 5, 2001 8:33 pm
... A result well sort of. I've just got my other Binetone Eurotel 1500 back from Crucible Technologies and it works just fine with Comfort, so my spare one...
702
John Engelhardt
john_engelhardt@...
Aug 5, 2001 8:33 pm
That's what it was. The 12V power to the three sensors and KP #2-6 and DP #1-2 blew 4 fuses. I guess I should have powered down my 12V (Axiom) supplemental ...
703
steve
steve@...
Aug 5, 2001 8:34 pm
Hi, Any examples would be much appreciated. Steve. ... From: Rod Stephens To: comfort-technical@yahoogroups.com Sent: Monday, July 30, 2001 10:16 AM Subject:...
704
Jonathon Greiff
jgreiff@...
Aug 6, 2001 11:54 am
Are there any plans to increase the nuber of X10 Addresses that can be activated by Comfort up to the full 256 instead of just 32 ? If so could you let me...
705
Andrew Roberts - Comf...
andrew@...
Aug 6, 2001 11:56 am
Are there any plans to increase the number of X10 Addresses that can be activated by Comfort up to the full 256 instead of just 32 ? If so could you let me...
706
L Y Chiu
chiu@...
Aug 6, 2001 2:48 pm
To clarify further, there is no fixed number of X10 commands which can be sent out by Comfort. All the 256 addresses can be send. It depends on how you...
707
Dan Hoehnen
dhoehnen@...
Aug 7, 2001 12:41 pm
And, to clarify even more.... :) If you use ACE and/or CWI (Comfort Web Interface) then you can configure ACE to have Comfort send X-10 commands in response...
708
steve
steve@...
Aug 7, 2001 8:59 pm
hi, On a fully expanded system wont program space be in short supply ? Steve....
709
Mike Griffiths
mike@...
Aug 8, 2001 12:59 am
Anyone know the operational distance of this unit http://www.visonic.com:8080/visintl/VisonicI.nsf/Products+on+Web/4CB4AF5EB0D ...
710
L Y Chiu
chiu@...
Aug 8, 2001 1:11 am
Steve You have to carefully plan the utilisation of the 255 Responses when you have 64 inputs and outputs and are doing a lot of things with Comfort. We are...
711
steve
steve@...
Aug 8, 2001 11:04 am
I could see things getting tight even though i have just started to grasp the programming. I may not expand to 64 but will be heading that way. I do intend to...
