After having a new curtain rail fitted on Friday we discovered that on setting comfort an open zone was being reported. Initially I though this was an open...
792
Andrew Roberts - Comf...
andrew@...
Sep 4, 2001 11:15 am
Dear All, Please be aware that Comfort Home Controls (UK) will be on a TOTAL shutdown for 2 weeks from Friday 14th September to Tuesday 2nd October 2001....
793
L.Y. Chiu
chiu@...
Sep 5, 2001 12:36 pm
We have found it difficult to eliminate the click. In fact it is much improved from earlier versions. A lot also depends on the Amp IC in the keypad, so you...
794
David McGowan
dmcg_58@...
Sep 6, 2001 1:02 am
Hi I'm trying to use 2 inputs on Comfort to measure analogue voltages using action 89. Both voltages to be measured are between 0 and 5 volts. What type of...
795
L Y Chiu
chiu@...
Sep 6, 2001 2:44 am
Note that only the 8 inputs on the Main Comfort PCB or Salve Modules can be analog, not the LEM Inputs. You can define the zone type as any non-alarm zone type...
796
Chris Howard
chris_howard@...
Sep 6, 2001 9:00 am
Is it possible to have an X10 movement sensor (I have just got one for my shed) to make an announcement on a keyad. I am not sure I want a fully blown alarm to...
797
Andrew Roberts - Comf...
andrew@...
Sep 6, 2001 9:58 am
Chris, This was covered in the Comfort General group a few months ago ago. Zone Announcement (Action 1, or Response 59) can only work on zones and not ...
798
Keith A. Milner
maillist@...
Sep 6, 2001 12:03 pm
--On 06 September 2001 08:33 +0000 Chris Howard <chris_howard@...> ... If you set up an X10 triggered response which plays an announcement on the ...
799
L.Y. Chiu
chiu@...
Sep 6, 2001 1:25 pm
... announcement on the ... to then ... Yes, that will do it (unless you have a very old version) If you want the announcement on one particulat keypad, you...
800
Stan Ferguson
cedric@...
Sep 7, 2001 10:10 am
Hi All, I was wondering has anybody controlled a heating system(zone valves,ignition) with comfort(not via or over riding conventional controllers). Using the ...
801
Andrew Roberts - Comf...
andrew@...
Sep 7, 2001 10:13 am
Subject: [comfort-technical] Heating Control - Counter Responses ... valves,ignition) ... Stan, We have an action code 89 which can read analogue inputs, we...
802
Chris Howard
chris_howard@...
Sep 7, 2001 12:59 pm
... <chris_howard@i...> ... one ... have ... KP8 ... Chui, Are there any plans to bring out an additional action code that allows you to speak words from the...
803
L.Y. Chiu
chiu@...
Sep 7, 2001 1:06 pm
... I hadn't thought of it. it may not be an easy task. Andrew's method of using receiced X10 response to trigger a realy would allow you to announce works...
804
Andrew Roberts - Comf...
andrew@...
Sep 7, 2001 3:09 pm
New Cable Manufacture BT3002 for Comfort We are proposing 3 Wiring Plans for Integration of Comfort with PC, TV, VCR and HI-FI. It includes the new UCM01/A...
805
Dan Hoehnen
dhoehnen@...
Sep 7, 2001 3:51 pm
If you have a PC connected to Comfort then you can run ACE or CWI and then you can play WAV files and/or speak any text string using text-to-speech in response...
806
Hawes,Timothy Edward ...
haweste@...
Sep 8, 2001 2:35 am
A slightly off-the-wall solution may be to invite your poshest friend / colleague / associate to speak the required phrases. At least it wouldn't be ones own...
807
Stan Ferguson
cedric@...
Sep 8, 2001 2:35 am
Hi All, Can anybody tell me is there an action code for announcing words on the keypad from the word list IN TABLE 40 within responses. Thanks Stan...
808
Mark McCall
mark@...
Sep 8, 2001 2:36 am
... Chris You can create amazing sounding .wav files here... http://www.research.att.com/~mjm/cgi-bin/ttsdemo Just type in what you want to say and the .wav...
809
L Y Chiu
chiu@...
Sep 8, 2001 7:26 am
Mark You are right. This sounds really good chiu ... ===== Cytech Technology Pte Ltd 55 Ubi Ave 1 #04-06, Singapore 408935 Tel (65) 846 9701 Fax (65) 846 9065...
810
L Y Chiu
chiu@...
Sep 8, 2001 7:34 am
No, there isn't such an action. You can trigger a zone with Action 1 which will announce the name of the zone. This was also discussed yesterday in the thread...
811
Andrew Roberts - Comf...
andrew@...
Sep 8, 2001 10:13 am
Stan, You can attach Response 59 to any zone, this also has a 'User Control' (flag) which is operated in the Home Control Menu 6 (Door Alert OFF). You can also...
812
Mike Griffiths
mike@...
Sep 8, 2001 2:07 pm
A nearly related question I would like to use the feedback input facility on Control Menu for virtual inputs as will as Zone inputs It seems a pity at present...
813
Keith A. Milner
maillist@...
Sep 8, 2001 10:06 pm
If there are plans for any upgrades to the comfort firmware, I would like to request support for more user flags. The main reason is that, with the...
814
L Y Chiu
chiu@...
Sep 9, 2001 1:59 am
Keith Comfort firmware is constantly neing upgraded. In fact, more flags are planned for future revisions Will there be a manual control of the curtains which ...
815
L Y Chiu
chiu@...
Sep 9, 2001 2:05 am
Mike You can use virtual inputs, by sending the I! to the UCM to update the on/off status for feedback. This still needs a physical zone on Comfort. You can...
816
Keith A. Milner
maillist@...
Sep 9, 2001 3:03 pm
Chiu, --On 08 September 2001 18:59 -0700 L Y Chiu <chiu@...> ... No there isn't. For those using X10 controllers to operate the Butlers,...
817
Michael Mc Aree
michael.mcaree@...
Sep 10, 2001 10:56 am
I have set up my system and the phone seems to be working fine. I get local phone control and Caller ID passed. The only thing that does not seem to work is...
818
Andrew Roberts - Comf...
andrew@...
Sep 10, 2001 11:05 am
Michael, Have you recorded your 'Greeting Message'? (Menu 2,6) Is Comfort TEL Out connected to the Telephone line (Solely) and TEL Out connected to local house...
819
L Y Chiu
chiu@...
Sep 10, 2001 11:14 am
I can't conclude what the problem may be, but a good test would be to disconnnect everything from the TEL out terminal block and see if Comfort can answer when...
820
john.engelhardt@...
Sep 10, 2001 2:52 pm
Does anybody have a macro that would allow a specific Zone Type to be DELAYED when arming to AWAY mode? I want to arm system from keypad in the house.... open...
