You should use a Timer to delay each set of commands when ypu have a lot of stuff to send out to Cbus eg Resp 1: Do Response 2 after 1 second using Timer 1 ...
Hi there, I installed 2.0.2 version of comfigurator and set FS34 as default template and noticed that straight away the number of timers and time programmes ...
Hi Andy, Thanks for pointing it out to us. To handle this problem at the moment, you could save the converted file, then open the file again. You should be...
Upgrading to Ultra IIHi Andy If you save the file after conversion then close CF and restart the program and reopen the file, the timers should be ok. Best...
Here is the sound Com os melhores cumprimentos, Rui Rego dnt_disrego_novas_tecnologias www.disrego.com <http://www.disrego.com/> Telemovel: 917 195 328 ...
I would like to arm just the ground floor in night mode. That would be easy if Comfort ad groups. The way I think a can do that is with a response - if night...
After arming the system (in away or night mode) the keypad does a siren sound and then it stops, moments later the sound comes again. How can I turn off this...
battery was unplugged when I checked the voltage, though not under load. L Y Chiu <cytech_tech@...> wrote: To get a true measure of the battery voltage,...
You have programmed or downloaded the wrong siren types or sound types Check the setting of Alatm Types > siren types for Away armed and Night armed or do an...
Use Zone Types to make active zones on the ground floor and make inactive zones on the top floor. Zone Type 18 is immediate only in away mode. You can use this...
As I said, you can only measure the true voltage of a battery under load, not while it is unloaded ... Cytech Technology Pte Ltd 55 Ubi Ave 1 #07-04, Singapore...
Just wanted to confirm a wiring config for a Hochiki smoke sensor.... the sticker on it says it is a non-latching relay base, - I'm assuming from this that I...
If the Smoke sensor does not need resetting you can supply from 12V, but there should ve no harm is supplying from S12V as removal of power for a while should ...
If the Smoke sensor does not need resetting you can supply from 12V, but there should ve no harm is supplying from S12V as removal of power for a while should ...
Hi Paul, Supply the sensor from 12v, it shouldn't need resetting if it is non-latching Best Regards Andrew Roberts http://www.home-control.co.uk/ ... From:...
just installing comfigurator 2.0.2, it says the below on the cytech website, where is this file ? (ccldef.zip) After Installation, download the file ccldef.zip...
Adrian please ignore that instruction, it was left over from the previous, and will be removed ... Cytech Technology Pte Ltd 55 Ubi Ave 1 #07-04, Singapore...
Hi, When I swap my board out for the new Ultra II, will I have to take the battery out of the siren when it gets disconnected to prevent it sounding while I...
Can anyone help? I have an old light sensor module and wanted to confirm how to wire it. On the board the connectors are named CN1, CN2 and CN3. Does anyone...
Rob, a few posts ago, see the thread " External siren hold off" Best Regards Andrew Roberts http://www.home-control.co.uk/ ... From: "Rob Kirkbride"...
Cytech / Chiu, I am not able to record user names or greeting messages from the answeringmachine of comfort II. As soon as the beep sounds, the voice menu is...
Hi all, For anyone who's done the upgrade just wondered if anyone had got any thoughts to share on there experiences/how it went. I'm happy I've got all the...
Everything is pretty straightforward, - but one thing I did notice... With the board fitted in the case, and the LEM (if you have one) mounted in its...
It is possible in Portugal? This may not be very common in other countries perhaps? It has to be quite widespread for this to be feasible to develop ... Cytech...
8219
Pam Zeiler
komfort@...
Jun 8, 2006 1:04 pm
You can send SMS's from South African landline phones. Regards Pam Zeiler ... From: "L Y Chiu" <cytech_tech@...> To: <comfort-technical@yahoogroups.com> ...
Hi all, For anyone who's done the upgrade just wondered if anyone had got any thoughts to share on there experiences/how it went. I'm happy I've got all the...
