Mariss, Is the data random or zeros, or some other constant?. If it is the latter it is probably being cleared by a start-up module? If it is random, don't...
From: "terozi" <terozi@...> ... Even worse, the law says that the state installs the colection containers, one or more in every city. Each time one of...
Peter, It appears to be random because looking at the hex code as op-code neumonics makes no sense as assembly code. Details: 1) I'm using a RCM3720 and WinIDE...
... Does the (OS, executive, RT scheduler, whatever kernel you have) do a memory test, memory sizing, memory clearing process? This may take serious hacking ...
Hi, Does the error occur during a simple strobe of the reset line (rabbit power up and active), or only at a power cycle reset? Jeff ... data ... will ... I've...
Jeff, This only occurs when the program restarts from main, (after reset or power-up). Interestingly stuff located above 0x20000 is not affected. I alternate...
Hi, OK, I was thinking there might be noise on the inactive low CS2 line of the BBU RAM which should be held low until the CPU has control of all of the other...
Hi Mariss, I just wish to say that having sent 3 drives back to Geckodrive some 6-8 months after purchasing them and damaging them. They were replaced free of ...
Hi Mariss, I don't play with rabbits(yet), but if it is random then it is not being initialised by a start-up module. If it only occurs on power up, it ...
Peter, By random I mean the pattern makes no sense as executable op-code instructions. It is not random in the sense the same pattern repeats exactly on every...
Mariss, If it is repeatable then it must be being written to by a start-up piece of code. Most processors also have a reset state value for their registers and...
... Not familiar with the processor, but.... I've seen this kind of thing happen. One possibility is that you're getting something called repeatedly, and the...
Peter, None of that applies. I'm so frustrated I'm ready to throw the nearest G-Rex against the wall and stomp the living crap out of the sorry remains.:-) How...
Mariss, See below, Cheers, Peter. ... No, No, No! Don't throw it against the wall, throw it at me. :-) ... We could start the Rabbit VS Arm processor battle....
Peter, A week from now this will be a little bump. A week from now there will be another hysterical tragedy certain to end the world as we know it. Did the...
Mariss, Yes, well money can buy most thinks. You can even buy immortality (cryogenic freezing). Not sure how the money back guarantee works though. :-) In my...
... OK, there are a couple of possibilites. One is that the computer is not being held in rest during power-down, and it crashes when some chips quit...
Jon, I expect that Rabbit would have covered the hardware problems. Using the backup battery would be very common on those modules. Your points are very valid...
... OK, I wasn't sure whther this was on the Rabbit board or on the G-rex board. If it is all part of the Rabbit, then the hardware, at least should be ...
... I USED to have the temperament for it, but that was back when computers had rows of switches on the front panel, and you could tell what it was doing by ...
Hi Guys: Version 1.0 alpha of MAchIV can be found at www.machsupport.com . It now handles the monitoring of limits, Estops, and can do homing runs . The homing...
Hi Art, ... So should we purchase the G100 from you (to get the correct firmware)? or buy it from GeckoDrive? -- Dave Hylands Vancouver, BC, Canada ...
Dave: Mariss will be offering a G100 already programmed with release firmware in it as of next week. It will be updateable in the field from that point ...
Hello, I am having a problem with two Minertia R02MAKOE servos which are connected to G340's. The first problem is dithering, I already have the jumper that...
... Hey, if it doesn't have blinking lights and rows of switches then it ain't a real computer... -- Member of the toughest, meanest, deadliest, most...
... Hey, AAMOF there was a discussion of RTL going in one of the other lists I carry here just in the past day or so, and I was able to remember some ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
