Well done What about a higher voltage version Regs Mark _____ From: geckodrive@yahoogroups.com [mailto:geckodrive@yahoogroups.com] On Behalf Of Mariss...
Now that the V drive is out, any chance Gecko could take a stab at writing a G-100 white paper addressing wiring up specific classes of devices for the...
Yes. We will later make a very small PCB that carries just the opto with its LED connections rearranged to common anode (COMMON 5VDC). Kind of like a really...
Hi Mariss, I would like to second Steve's recommendation, I also would like a user/hookup manual for the G100, addressing the limits of voltage, current on...
Mariss, That will be good as one of the features on our breakout board is the ability to drop the 5 volts when the EPO switch is pressed. Robert Colin Campbell...
I received some of the first batch of G203's that Geckodrive is now selling. I installed them in the same 3/4 axis case that I use for my G201 and G210 step...
Hum, this may be a silly question but I figure I'd better ask so as not to let the magic smoke out... The silkscreen on the top my of G340s show a series...
... now ... for ... use ... and ... pulse ... program ... none. ... after ... at ... steps ... in ... run ... working ... already ... stepper ... Dan: Your...
Mariss, Thinking of things while I wait from my 203v's to come in , I have an other question. I am using the disable input on the G202's and ground it to pin...
No. The G203V DISABLE input uses the same COMMON as STEP and DIRECTION. COMMON is now ground, not +5VDC. You have to apply your controller's +3.3V, +5V or a...
Anybody out there using linear encoders with Mach and/or Geckodrive Grex G100? I'm thinking about using a Renishaw 0.5 micron resolution scale tape and...
James, there is a ton of info here. http://www.thewarfields.com/MT/MTLatheCNCDrivers.htm plus I cannot say enough about this site be sure to look at everything...
Thanks Archie, Jim C. archie road <jeep_32@...> wrote: James, there is a ton of info here. http://www.thewarfields.com/MT/MTLatheCNCDrivers.htm plus I...
James, there is a ton of info here. http://www.thewarfields.com/MT/MTLatheCNCDrivers.htm plus I cannot say enough about this site be sure to look at everything...
What you need is a PD servo instead of a PID servo. Contact me off-list and I can describe how to remove the integrator from the G320. A soldering iron will be...
Not wishing to sport a competitor on your site Marriss, but I may be able to save you some grief. A Rutex drive would probably handle this, not because it's...
I don't think you will have a problem with the opto. I took one of those cheap chinese brush type grinders and placed it touching the disable and step and...
Yesterday I installed my 3 axis control box using the new G203 on my mill drill. The mill drill has been retrofitted with ballscrews and my 452 oz in stepper...
Thanks Mariss, I sent a request via your website contact. If that doesn't work you can contact me direct thru homeshopaccessories@... Thanks, Joe V. ...
Tom, Noise immunity is dominated by the impedance of the signal-line driver, not the impedance (or sensitivity) of the receiver as long as it has a significant...
I'm not so sure that a servo or stepper motor drive will work for this application. You're essentially wanting to use the motor as a rotational spring right?...
Any servo drive I'm aware of will do this. As long as it has some sort of windows software, you can "turn off" or change any gain parameter you like. If you...
Mariss, I was wondering what the long term availability of the G202 drives and the long term availability of the new 203 drives will be, the best you can...
Long-term component availability is what drove the G203V design. All our drives previous to the G203V use CD4000-series logic ICs. This IC family is entering...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
