Thats because Netscape 4 doesn't support a lot of html scripting, need to update to 6 (free at netscape website) a lot of commercial sites have to 'double up'...
Micheal, Where do you meet, am in Leamington Spa, love to give you a bell, but I can't find a phone number in the post/database! Simon ... November. ... do...
Hi Rick, Yes I have a Mackay part No. M114 but at this stage I dont know who stocks them. Repco dont here in NZ. On going thru their catalogue I saw quite a...
Hi Ken, Bearing in mind what you have mentioned and which I have'nt even considered what do you think of the ones in the book? Although to me neither type...
Hi John, You learn so much on this list. So what you are sayiing then is that the mounts should not be at a direct right angle from the motor but should be at...
Hello Rory, I have some jet sizes for a 32DGV twin choke carb. 1st 2nd Choke size 23 24 Aux venturi 3.50 3.50 Main Jet...
31227
Lewis Family
lewis@...
Nov 1, 2001 9:10 am
Hey Simon Get that smile off your face. Regards Graham Lewis ... From: Gigney, Simon M <simon.gigney@...> To: <locost@yahoogroups.com> Sent: Tuesday,...
ive just found the pedalbox in my pile of bits(a year since i last saw it), i did not realise how sutable it is(seems) for the job, i looked in the book and...
Those running Netscape 4, it doesn't support Dynamic html (although the protocol was available before they launched it...) but you can get a free update to...
31230
Lewis Family
lewis@...
Nov 1, 2001 9:31 am
Julian One of my best friends is a Pole and his name is Julian Regards Graham Lewis ... From: Julian Dziurawiec <JDZIURAWIEC@...> To:...
The diff centre is not offset - just the pinion and the reason they are offset is so they can have axles the same length . I doubt you will find one. Cheers, ...
Hi Peter, Have a check with an industrial supplier rather than automotive. Cheers, Tricky H. AussieGAZshocks rhargrav@... ... From: "peter-sutton"...
31234
Darryl
sbprint@...
Nov 1, 2001 10:28 am
OK I'm obsessed. Borrow my mates 3 piece rims, fit them to the car and thought, doesn't really suit my car, look great on his though. Pissed off I sit down to...
Alan thats my problem, will be fixed, was meant to be done last night but the ftp program was playing up, ended up having to re-install it, the other problem...
your messages are making it to the list. Alex ... From: John Holmes [mailto:johnh@...] Sent: Thursday, November 01, 2001 8:55 AM To:...
31240
imakora@...
Nov 1, 2001 4:05 pm
Dear List, Just offered up the axle to finalise the position of the shock absorber brackets, and it looks as though the left hand side is about half an inch...
Julian, I too am building a 6 cylinder Locost. is yours a straight or a vee? I'm using a V6 - either way, the sound is better than anything with just four...
Ian: Axels are usually straightened by running a heavy weld along the housing surface, which draws as it cools, pulling the axel into true. Ed ... From:...
Never heard a V6 sound good they just sound like two 3 cylinders out of phase and need all sorts of complex dampers and counter balancers to stop them...
Peter-I think the stock mounts are a bit wimpy but seem to work. location seems ok.a piece of cable on each side going from engine back to chassis would allow...
... From: Andy MacFadyen To: locost@yahoogroups.com Sent: Thursday, November 01, 2001 4:48 PM Subject: Re: [locost] 6 cylinder locost Never heard a V6 sound...
... From: locost@yahoogroups.com <locost@yahoogroups.com> To: locost@yahoogroups.com <locost@yahoogroups.com> Date: Friday, November 02, 2001 5:48 AM Subject:...
Hi all, I've followed a thread on the bike engined ring, one of the factors that may contribute to a lack of self centreing may be the stiffness of a new/recon...
Simon, Very nice site - keep it up! Personally, I don't even have enough time to build the car, let alone run a website like that about it. Nice bit of...
