Thanks for that. Guess we got the same mill with a couple extra pots. At that time here the Celica used the 2.4L version of the "R" series, the 22R, (as did ...
Folks, After having our monthly midlands meeting I've been left with a quandary. I originally wanted an Ali floor but talked myself out of it. A Steel floor ...
yep - that didn't make too much sense. What I meant to say was the cycle wing bracket touches the headlight... Cheers Anthony ... From: Roebuck, Alex To:...
Alan, Thanks for that - I'll use those numbers. Regards Anthony ... From: locostuk To: locost@yahoogroups.com Sent: Tuesday, October 01, 2002 8:37 PM Subject:...
Westfields have had ali floors for donkeys years, so there isnt a problem with them. Gauge? I think mine was 1.6mm, but not sure. They are certainly a lot...
I would have thought the total 'actual' weight would be less than 600kilograms. A guy over here in Australia recently took his car to a public weighbridge to...
Ah! Is your steering rack central? Are you showing the same number of threads on your trackrod ends? The Westfield manual suggests an initial setting of 4...
What the SVA is looking for is the weight the design is meant to take and so the if you have a car wihich weighs in at say 650kg unladen and you put that on...
Yes - they are the 5" ST light units. I think I'll try and limit the amount of travel the rack will allow to that side. I've set-up the tracking as best I...
Hi All, I'm new on this group but I have been pointed here to get an answer to my questions, so here we go. What dampers do people recommend for the Locost?...
I've taken the liberty of pasting a message dated 2nd of September from Cougar Racing about the Nitron (now known as GTS) Shocks. I have some of these shocks...
We had this discussion a few months ago - the general agreement was that 3mm of ali gives you as much strength at steel, more rigidity, for a bit less weight. ...
The Westie floor is def. thinner than that from what I remember, but what it is I don't know. James ... From: David Jenkins [mailto:d.w.jenkins@...] ...
Steve There a West****d club in Norfolk and as a Tiger owner I have been invited to join them on a airfield day so I don't know if they would be of any ...
Folks, We seem to have one of those viruses going round group members that attaches itself to a recent e-mail and sends itself to names taken off the unlucky...
As an addendum its called the bugbear virus. If your printer suddenly goes a bit odd, then this is an indication that you have the virus. More information and...
Hope this helps youse guys with the bugbear Fitzy Note: forwarded message attached. __________________________________________________ Do you Yahoo!? New DSL...
Hope this helps youse guys with the bugbear Fitzy Note: forwarded message attached. __________________________________________________ Do you Yahoo!? New DSL...
... Having not finished my Locost I can't comment on what works well on 7's. But my money for high quality dampers (from use on other cars) has to go with Avo....
... Mike, Don't think simply about mass. There are other, as important, factors. I went steel (galvy). Largely because for a given strength you'll have less...
Hi,
Building a locost, it can be handy to have as much manufacturer information
as possible, in my trade as a specialist mechanic for a particular car make...
Due to an upgrade to K-Series power I am selling my current Ford Crossflow as a complete unit; from inlet manifold to through to exhaust system – all you...
Hi Folks, I have at long last got round to welding the chassis up. As I bought my box section sometime ago and at different times I now find that I have two...
In the US it is sold by gage and from what I've read most builders (myself included) have used 16GA, which is about .063" or 1.6mm Bill ... bought ... I ... ...
Nigel: The flex rate of the two different wall thicknesses could be a problem. My thought would be to use one thickness for the horizontal pieces and the other...
