Well again this place is getting too quite, so. My old sears saw oil pump finaly went out completely. I have had it for 12 years, got it at one of those...
I also have a 084 now and it´s great but the ball in the end of the cable came of for me too. The saw also pulls back when starting almost every time when the...
... the cable came of for me too. The saw also pulls back when starting almost every time when the engine is warm. After i take off ff the spark plug and pull...
The secret to success is to reconigize market conditions, and take advantage of them. I am sure some guru said that. But my thinking;;; I got a log sitting on...
It turns out the oiler cable for the STHIL .084 is back ordered, and do not know when one will be received. but reently I have been running STHIL chain, and...
Sat. we finaly had some sunshine. Although I had a very rought night Friday, as I am coughting too much , and tooo much fluid developing, at times, I was...
We lost a large red oak in the April storms. As we speak, it is being cut in to boards on a Wood-Miser(Mike Butler, BDFT Lumber, 860-379- 3578). It is far more...
Finaly the cable arrived, and is installed. Somehow it makes one feel good to be able to give that extra shot of oil for only $19. Yesterday I was in Home...
It seems near on imposible for a man to get his moneys worth out of anything in todays world. It does not bother me to paay a good dollar, but I at least...
I have one. They are low quality. It works though. there is a little learning curve... you have to get to know "yours" (because they are built with such low...
Yes it will. To both questions. 0-35 degrees. Just visited your website... Nice. I'll likely be buying from it. ... Will this grinder work to sharpen .325...
The harbor freight grinder is OK; I have a friend that has it. I'm about to buy one of the "Northern Industrial" grinders. They are a lot more expensive;...
Hi All, I have an SMG mill, the 13 horse honda model. I made the mistake of trying to adjust it to handle an overlong band, and now I can't get tension on it...
Hi back again last time I posted I was trying to upload pictures and never was succesful glitch someware probably in my old slow and outdated computer : ). ...
James, I could not be of much help on the Kiln, but was glad to see you got your pro cut going and having fun, i also slow computer service due to location,...
James, I built one closely modeled on the design by Dr. Wengert at Virginia University. I say closely because I used cheap and scrap materials where possible,...
I have and older 090 and an alaskian mill I am going to need a new bar and can't really find anyone who stocks one. I'd like to go at least 42" I can't find...
... any ... where ... It ... have. ... of ... at it ... It only cost $30.00 plus shipping. Check the discontinued items on their web site. It even tells you...
Unless the bar is worn so bad the drags rid/bottom out,you can dress it . A rake file on the sharp riidge build up on both the top and sides of the bar. There...
believe it or not I have been milling with a 60cc mcculloch timber bear chainsaw, and having lots of fun. Problem is nobody seems to want to work on this old...
... bear ... Search e-bay or a local dealer for a re-build kit for the carb.Initial carb settings for your carb are one turn out from a lightly seated ...
I smokes to beet the band and ... Several areas possible on older saw, low compression, compression should be when new pushing 125, 90 is getting boder line,...
Hi Jay, Have you got any worthwhile answers to your questions yet? If you don't mind I would like to put in my two cents. It may be of help to you. When you...
I have an older Delta saw mill with a 10 foot blade and an 8 horse honda motor. It was running fine and started making excessive noise and then jumped the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
