... Harold, the Huskys are 385/395s that get the air time. Although the old time feller has used a 3172 Jonsered which is the same as a Husky 372. So far,...
im new to milling lumber i recentlly bought a 066 off e bay and an alaskan mill from northern tool at there demo days im too tight to buy the slabbing rails...
... buy ... start ... is ... if ... counstruction ... I have a 20' section of aluminum extention ladder that I use for some of the longer logs that I mill. You...
Look at the pictures in Poor Boy Construction, The first page of pictures is the first vesion of a copy cat of a circular saw mill set up. It has since been...
I don't know if I have a better dealer or just better circumstances but I ordered an MS441 for normal use and occasional milling. I was there at 8 am. They...
It is not the dealers. I kive right in the middle of timber country, but the hydra axe is used, not the saw. Even limbing the trees is done by machine. Most of...
I got the new MS660 in yeststerday, with full skip chain, quite truefully the power head innstantly looks small to me, but if th sun shines today, I will see...
go to google and type in HH0 gas generator Harley Scott CEO Ecomill-Ecological Forest Milling 77 Royal Melbourne Avenue Connolly WA 6027 Western Australia Lat...
go to google and type in HH0 gas generator Harley Scott CEO Ecomill-Ecological Forest Milling 77 Royal Melbourne Avenue Connolly WA 6027 Western Australia Lat...
A bit off subject here, but here is an examle of what Harley is talking about. There are different steps, each burns differently, or hotter. I will be using...
Dear Bill 1: How many kw-hr of electrical energy is required to convert 1 pound of water into HHO? 2: To get 1 HP from an engine, how many pounds of water...
Kevin Chisholm
kchisholm@...
May 8, 2008 3:40 pm
13462
... It takes 11 3X5 stainless steel plates, using a few ounces of KOH with the voltage being approximately 2 1/2 voltsat the nutrual plates in the center of...
Let's get my mistakes out of te way, First takeing the dogs off, bout sliced my hand off, so what's a little blod ? Next,I flooded it, cranking just lke I...
Up here in the northern part of Arkansas the air probably gives more power to my 066 than your new one. Or maybe we get a more potent fuel delivered to NW AR...
dear group, water is and can be and always will be a fuel, motor vehicles can run on hydrogen, fact. try getting a steel bar molten with a gas axe and then...
Kirt, Rocketscientest, now daddys boy came in from work, and proceeds to tell me a story about Ralph, a fellow where he works, that trims trees on the side....
Dear Harley ... If water is indeed a fuel, it will have a heating value, like oil has a heating value. What is the heating value of water? How do you set fire ...
Kevin Chisholm
kchisholm@...
May 9, 2008 1:36 am
13468
That 8 tooth sprocket will make the saw work harder to do the same cut since it has to pull 8 pitches of chain (=faster chain speed) for every revolution of...
I've never seen a Sperber mill. Is there any information on the internet on them. I'd like to see some pictures of one. Mark ... From: "Kirk & Judy"...
... . I'm building a chicken coop right ... before the ... Mark,isn't it amazing how we become dependent on being able to make instant lumber for these...
Mark, I found a couple sites that have some pictures of a Sperber mill I used to have some photos of our project but they are lost. Sperber was very innovative...
Bill, Do your guineas stay close enough to home to control snakes? Mine were shy and liked it out in the pasture where they (the guineas) were good food for...
I have not had any up here for a few years, but the ones I use to have did.And they would get the snakes. a lesson on team work between species. This one gunia...
I don't have first hand knowledge of keeping guineas but my aunt and uncle kept them for years. When they had to buy eggs or chicks, they kept them for a...
Mike Ryschkewitsch
mgrysch@...
May 10, 2008 10:41 am
13476
Hey guys - I've been reading through the sawmill plans that are posted. Whoever wrote them references using a vicegrip dog. I get the idea, the vicegrip has a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
