Found in Sacramento Bee Classifieds, CA JOINTER 30", Yates American 7 hp mtr, 3 phase, w/rotary converter, round cutter heads, 4 blades, 4'x8' long, $3500....
HI all, Well, got some results back from my service provider, I guess there have been 1600 hits on the W&M mortise machine site. I only heard of a few people...
GHP
gary@...
Jun 1, 2002 2:08 pm
14187
Gary, I'm jealous. That isn't the one that came from Charleston, SC on ebay is it. Just to think I could've drove down. You've got one nice machine there. I ...
Don, You really "Stumped" me with that message! (Ar!Arr!) After I posted that question about the "Handsaw" I went back and saw (groan) that you had said...
Brian, Yes I was prepared to go to...ahem...$1,500.00 for it. The reason? The seller told me it was Military Surplus. I figured it had about 20 hours use on...
GHP
gary@...
Jun 1, 2002 4:20 pm
14190
OK, opened up the capacitor housing... and found my original receipt and even the box the replacement came in! From the same shop I plan on visiting soon... so...
You can still get NICE bearings they are now a subsidary of SKF and should be available from your local bearing supply company. You can also download...
Any Dunlap/Sears guys out there need a motor? 1750rpm, 115v, split phase, double 1/2" shaft, start/stop toggle, and power cord. $20 plus UPS. See pics: ...
I have several old benchmounted tools with motors that have a bar on the bottom. the bar rests on two small cast iron "U" shaped cuffs attached to the bench....
The front multiple pulley (in line with the drill) is a casted part with a pipe/sleeve . This pipe's inside is grooved and slides up and down on the main axle....
I purchased a belt cover for my Delta W/M BS in the fall for $43 and have seen 2 others go for similar amounts of *dead presidents*. Mine was NOS in the...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the oldwwmachines group. File : / Click...
hi dave maybe i should part out that delta 14" metal/wood saw , eh?? mike ca Has anyone ever heard again from the guy in MA that had all the Delta stuff for...
hmmm...maybe I'm a bit dumb here guys, but like...I clicked and got just yet another credit card offer... GHP ... From: <oldwwmachines@yahoogroups.com> To:...
GHP
gary@...
Jun 2, 2002 11:00 am
14201
... Heh, heh, heh... We aren't helping much either by having a forum devoted to the insanity either. Know what I mean? I would suspect there are more than a...
I would think that the final price on a machine would depend heavily upon it's relative distance from the buyer, in that freight and transportation charges,...
... We've had this happen twice now. At first I figured I'd go in and ban the spammer but then it dawned on me, why not set them up to receive all the e-mails...
Yes, it's true, chapter 9 is up. This is where the reader picks up our great adventure in Virginia and prepares himself for the bus ride back to Montana. If...
Yesterday I picked up a Delta Rockwell Homecraft table saw that also includes a disc sander, a jointer, and a drill press, each of which look like they connect...
... includes a disc sander, a jointer, and a drill press, each of which look like they connect to the table saw stand. From what I have learned, the saw was...
Keith: Probably NOT a good idea and I say especially so if the e-mails will inadvertently publicize our e-mail addresses! Matt - still unable to access his...
thewwl
thewwl@...
Jun 2, 2002 3:54 pm
14210
now THAT i like... good going KB!! ... got just yet...
Why not short pieces of suitable sized angle iron - drill an appropriate sized hole in each and then hacksaw or file out the rest of the opening. Two screw...
Hello to everyone in the group. I've been lurk'in for a month or two and have picked up a wealth of info here. Just started get'in some 'arn in my garage. I've...
... appropriate ... opening. ... on ... source? ... I have some like this- rubber grommets in a U shaped frame allows mounting shaft to be supported and rotate...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
