While pawing through piles at my local Retool Store; I came across a W-T miter gauge with a 5/8" wide bar. It looked like something rare. I didn't get it...
... price ... leave ... Doug - It would certainly be much cheaper to get a phase converter, but you might want to know that Northfield recently started making...
I think that we here are mostly devoted to "old arn" talk, but who am I and seeing as how you asked a question related to your TS, here goes: First off, a...
This month's issue of Fine Woodworking has an article on making fold down extension tables. Clark ... __________________________________ Do you Yahoo!? The New...
Correct answer! I'm a little over an hour away. I must raise my bid to $1.50 to stay on top of this. Maybe we should talk. Joey ... saw ... band ... while...
If you believe $1.50 is a "more serious offer", I will counter with $15,000.00 and will deliver it to you myself. (since you are so near) Joking asside, I...
I've been cleaning up one of my junk piles recently, and realized I have about 4 or 5 big ancient motors, that I suppose are repulsion/induction, since they...
Well, unless things at the house blow up again(new roof last week), or the yard doesn't blowup(irrigation system killed by large truck) I will put the final...
... Pat - Since your much farther along with your restoration than I am with my 34-350 I'm green with envy ... can't wait to see the final pictures of the...
This doesn't exactly answer your question, but there are motors out there that have the capacitor located inside the motor housing and therefore the lack of...
... +++++++++++++++++ Nope just recognize quality and experience. ++++++++++++++++ The advertising department sells advertising to people who sell new ...
The sprayer is not anything you would ever imagine: http://www.bestgun.com/en-us/dept_103.html This has been the best find I have ever stumbled up on.... I am...
I have no interest in this: http://www.jimhainesauctions.com/diller.htm It only lists date of auction, no saw info, and some other tools going on the block. ...
Pat: Herešs my two cents worth. 1. align the blade with the miter gauge slots while blade is at zero (or 90 to the table) 2. tilt the blade to 45 and perform...
Pictures my folding TS extension at http://www.jmccaskill.com It's mounted on my '73 Unisaw. It's pretty simple to make, using a couple of 2 X 4 sheets of...
Bob: I was following right along till you said "tilt the blade to 45" and perform the same ritual.... The TS-Aligner is a dial indicator setup tool(you might...
Mr. Vaughn, Over and over I have been amazed with your knowledge about fixing, restoring, and tuning owwm. Dana Batory has a book out on old machinery. I can...
Me and the TS aligner go way, way back. At first they were mad at me, and then later we made up when someone tried to sue him for patent infringement. We...
Lynn My comments are subject to correction by the more knowldegable, here ... things are HUGE and rated at 1/2 or 3/4 hp, I assume it a power to ... An RI...
Again, youšre too kind. The book idea has been on my mind since 1990. Išve got several drafts and ideas already. Technology with the publishing people has...
... sure how to insert them into the message. And as always I would appreciate your comments, suggestions and input. ... My god lad, load them up to the photo...
In a message dated 5/1/2003 6:58:43 PM Eastern Daylight Time, ... I'am new to this qroup , but Iam keenly interested in sharpening brad point drills , Is there...
I am hoping to find an answer to this myself! Subject: Walker Turner Band Saw - How to establish age? Is there some way to establish the age of the above item...
... On several occasions woodworking writer Charlie Self has mentioned that you don't want to be writing for free. In the last 5 or 10 years that's what a lot...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
