I think I got some of the pdf file but the pic of hoe the motor is mount was not to awful clear. It looks as thought the motor is mounted at an angle to ...
Well, I finally got the planer home last night and it seems better than expected, it's mostly just double ugly. I couldn't wait, so last night I pulled the...
I'm rebuilding my #70 Powermatic TS. I re-bearinged the motor, and while I was at it, I mounted the 3 groove on the armature and chucked it up on the metal...
... snip ... bore, ... snip ... The Browning catalog shows a 3 groove pulley with a 2.95" O.D. and a 7/8" bore.The part number that I have in my Browning...
Keith covered it very well, but I will add: Most, if not ALL 12" blades are 1" bore. Anything past 12" is almost certainly 1". Freud has just about anything...
Any one have any ideas for a source for the knife guard, post, and spring on a Delta-Milwaukee 6" jointer. I can't seem to find a model number but the serial...
Since the belt spacing is OEM, like the Unisaw, an off the shelf pulley wonıt fit. Been there. My suggestion: use two good belts and shave off the broken...
Bed length will determine model number. 42 inch beds: 37-220, 32 inch beds: 37-307 If its the old pork chop style guard, they were discontinued years ago and ...
Try Machine Parts Corporation; they've done well by me! Gary ... From: lkasdorf <lkasdorf@...> To: <oldwwmachines@yahoogroups.com> Sent: Monday,...
GHP
gary@...
Dec 1, 2003 5:25 pm
37970
I use mostly Forrest and Systimatic. The Forrest woodworker II is a great blade for this machine. Make sure you buy the proper stabilizer. You only need one...
GHP
gary@...
Dec 1, 2003 5:38 pm
37971
I've been using a rather nicely matched group of 4 link belts for my 12-14" saw. I've not touched the adjustment in over 5 years, although it's needing some...
GHP
gary@...
Dec 1, 2003 5:41 pm
37972
... Hi Bob, what that problem be? Wondering what you meant since I'm in the process of putting back together my FFS. Thanks! Sal Garcia ...
For what it's worth, If your saw is like a PM 66 at all, the problem in finding a 3 groove is the very close none standard spacing of the belts. A standard...
First, thanks everyone for the response I got about using fillers on old cast iron tools. It was helpful, and exactly what I needed to know. I have another...
You might call around to the local electrical distributors. Some will not deal with retail but some will. Usually if you go in in work clothes they don't ask...
... <kunnenc@y...> wrote: "....I have had trouble finding many of the heater elements for old motor starters. I am searching at the moment for an element for...
Try a good electrical supply house for the brand you need. You can also check places like automationdirect.com , southlandelectric.com (they have a lot of...
Since I couldn't find anything in archives I ask here. I recently bought a 20" Crescent made about 1929. The wheel axles ride inside a cast iron hup (tube)...
Hello, I can't find much information on this topic and I thought people here might have an opinion on what the merits of a gear head drill press are over a...
... I didn't check for what you need specifically, but try these folks: http://www.cpisurplus.com/Merchant2/merchant.mv They carry alot of surplus and obsolete...
From the safety standpoint,geared head machines will not, of course, inherently slip like a belt drive job when the going gets tough. This reduces aggravation...
Posted several pics to the yahoo owwm album (listed as Powermatic 100) and a couple to the mothership photo section. Hope I did it right. Bob H ... From: Bob...
I recently picked up a Oliver Model 20a lathe. It is currently pained a light tan. Did Oliver paint all of their equipment the same color or did it vary over...
Thatıs a flat out awful looking machine thatıs in perfect restorable condition. Iıve almost envious. Looks like cosmetics is your only challenge. Nice...
Great site and great resource. Thanks. Forwarded the cannon page to a friend that does those. Bob Vaughan ... x [Non-text portions of this message have been...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
