Yow!!! Not just pink flowers, but PINK! ...and Bob, I see what you meant by visual impact. Well from the color scheme, we can tell she's a happy woodworker. ...
I bet she succeeded ... Do you Yahoo!? Better first dates. More second dates. Yahoo! Personals [Non-text portions of this message have been removed]...
Bob Just replaced a brake on a DeWalt Gr series radial. The old brake, tube style, just wasn't any good. [vintage 57]. I made a new control box,updating all...
I'll check that out. Thanks muchly. I didn't know Square D made a brake. I have been considering putting a VFD between the mag starter and the motor, but...
I have seen this done on one machine and two 5 HP 3 pHs organ blowers. The VFD slows it down very smoothly... Gary Seekonk, MA ... From: "Robert Vaughan"...
GHP
gary@...
Apr 1, 2005 12:54 pm
60278
I'm curious what it is about tilting table saws that makes them unsafe enough to scare several people? I'm only an occasional woodworker, and have only ever ...
I would love to see a very simple wiring diagram of that. If it comes to mind, and you can, hit me on the back channel with it. The VFD that's on my wood...
The VFD should be hooked directly to the line. No switches except a main cutoff. Then the motor is hooked to the VFD. Next your on/off buttons are wired to...
Robert, I'd have to look at it again. The blower must have a relay of sorts as there's a bell button on the console to start it (it's 5hp). I will find out...
GHP
gary@...
Apr 1, 2005 3:31 pm
60282
... Maybe so Bill. I had one of these: http://www.owwm.com/PhotoIndex/detail.asp?id=992 and was using a Unisaw at work. Somehow the perspective of the thing...
i too feel the quiver of disconcern when i think of the table tilting saw if you were cutting a sheet of say plywood at 45 wouldn't the scrap side want to...
I have a boice crane sander with many spindles, but need the sanding sleeves. The Boice Crane uses 9" sleeves. Any chance the ones mentioned regarding state...
Can't tell ya for sure that the State sleeves will fit. But I can tell ya that the sleeves from Grizzly will - and they are a H@#L of a lot cheaper than the...
I am pretty sure they are the same. You can go to www.freemansupply.com and then go to owners manual for the B-4 and see all of the sizes. Bill Miner ... ...
I have a Howell Electric Co (Plainfield NJ)110/220 single phase motor I would like to use to power my Delta lathe. It is 3/4 horse, 1140 rpm and is rated...
Tom: No help with the wiring, but you might want to reconsider using that particular motor. Howell motors are great (at least they were when they were based...
The speeds will be too low for using the printed data or relying on speed dial, but on a wood lathe, having a slower than normal is a good thing. The...
I have one, but no nameplate left. These motors were used on tilting table saws and a variety of Delta machines. Built by Marathon in the 1940s (the long...
... tilting ... the ... buy ... I have one of those motors which originally came off a combo, 10" tilt table saw and short bed 6" jointer. Table saw and...
In a message dated 4/1/2005 9:07:11 AM Eastern Standard Time, ... What would be REALLY scary to me, Bill, would be the blade coming loose when you run it in...
Mine's 12 inches! (ha-ha) No, it's not another bad April Fool's joke, I'm just wondering if anyone else out there has worked on a Walker-Turner/Delta type 20"...
Robert, I have not read the entire thread but for short: Use a VFD on 3 phase motors not on single phase. You can use a single phase in-3 ph out VFD to...
... reversible ... the other ... loose when ... I was wondering about that. It's never happened to me, but it does seem possible. However it seemed to me...
Thanks for all that. Not using a mag starter with a VFD is pretty much what I concluded. Its more a matter of the components won't work together rather than...
Bob Take the time to find one on the 'bay. I purchased my Square D for 35.00 +/- a few, in new condition. There is Jenks Equipment in Dc that probably still...
Thanks I'll check them out. Life would be simpler if it were plain vanilla 240VAC 3 phase, but its 208 and that's special for brakes, or at least I'm told...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
