... I knew that - and it is not as confusing as the hyphenated names we see, often on a particular gender. Better yet, Joe likes trains!! Bob Kutella...
Bob Kutella ... My guess on this is that Joe isn't the Lone Ranger and whilst I doubt everyone could pull some obscure (but important) factoids about certain ...
I recently bought a Crescent 36" bandsaw from around the 1950 era. It has a Peerless 3HP, 3 phase, 600 RPM motor. I have a small shop with only single phase...
Kinda makes me want to rush out and place a bid on it! GHP ... From: "Keith Bohn" <UnisawA100@...> To: <oldwwmachines@yahoogroups.com> Sent: Saturday,...
GHP
gary@...
Oct 1, 2005 11:58 am
69801
buy a phase converter. Gary Seekonk, MA ... From: "sammy23032003" <wclair4104@...> To: <oldwwmachines@yahoogroups.com> Sent: Saturday, October 01, 2005...
GHP
gary@...
Oct 1, 2005 11:58 am
69802
... If it were me, I would buy or build a phase converter. If you can find an old three phase motor somewhere that is at least three HP (more is better ...
... find an ... better ... than what ... salvage a 7.5 ... $150. ... was able ... often less ... not buy ... means that ... machine if it ... report it to ... ...
I used to run a lot of teak and had solid carbide knives made by Ballew Saw. I never really noticed too much trouble just more feed pressure. My own two...
If I remember correctly, that is a direct drive machine. We had one in a shop I worked in while still in high school. Finding a good 600 RPM motor isn't going...
GHP
gary@...
Oct 1, 2005 12:44 pm
69806
... was able to take advantage of every three phase machine ...<<< Keith and Gary - SSPs slippery slope pimps...
... board ... someones ... all ... I ... reality ... to ... then ... but ... said ... white ... little ... put ... are ... them. ... on ... Poor ... Buy that...
I'm re-doing a Dewalt GAO S RAS (14",3HP,1Ph ). I'd like to run a 12 Gauge coiled (recoil) cable from the motor to the back of the arm. I can find it in...
Gary, I am intending to use this saw primarily for resawing. Since you used one in the past, how do you think it will perform when resawing? Are there any...
Thanks John. The saw I'm restoring is also an older one, from 1948. I looked up tubular rivets on the McMaster-Carr website, but they don't seem to have...
Aloha, I want to say that I am sorry for bringing my personal drama to the forum and that was never my intention. I honestly thought that a lot of people here...
The castings on your machine will have numbers. These old numbers will also be the stock numbers of yesteryear. Guess what size blade it takes, then download...
I think we have all been there with some kind of a deal or another. I too start getting nervous fast when dealing with large sums of money and long distance...
I think a lot of us saw that and were as flummoxed as you as to its pedigree. We were hoping some would chime in and illuminate its background so the rest of...
Two options. The best way would be to download some manuals on DeWalt and check the directions on adjusting the various components square to the table, or the...
I've just decided to leave my employer of many years, and thought I'd take some decompression time on the train out east, stopping at Iron Fest on the way. I...
Steve Johnson
tooltimer@...
Oct 2, 2005 12:09 am
69821
Thank you for your help. Robert Vaughan <rmvaughan@...> wrote:Two options. The best way would be to download some manuals on DeWalt and check the...
... 12 ... arm. I ... for ... what ... starter ... =============================================== Phil I googled [coiled cord 12 ga] Got lots of good hits ...
Going to DC in 10 days to check up on the desecdant. Any recommendations on arn/wood/furniture stuff to see. Museum store flea markets? Gotta see the kid or it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
