Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the overunitybuilders group. File :...
overunitybuilders@yah...
Jun 1, 2006 2:33 pm
84
HI All, I just posted two files. They both show the work of Robert H. Calloway and shared freely on the internet. Maybe you saw them at one time or another....
... them up at a farm store. They (if I remember right) approx. 3" wide by 4" long. 1/4" thick. I am not sure how the mounting holes would effect it. Maybe...
Hi All, Those large ceramic ring "donut" magnets dont come cheap but today a catalog just arrived and if you look at page 163 you can find large ceramic donut...
Does anyone know how to remove the magnet from a load speaker? How about a NIB from a hard-drive, separate the magnet from the shielding? Thanks magnetman12003...
Tom I just dusted off and labelled an old drawing I had from that Calloway group days.I uploaded it into my folder. After much experimenting with "gates", I...
I took apart a hard-drive and had no trouble separating the magnet from the pole pieces. I just used a straight razor blade and tapped it lightly with a...
... shielding? ... Hi Jason, Go to your local hardware store and buy a quart or half gallon of ACETONE. A metal bucket also. Wear rubber gloves when you handle...
... Calloway ... with ... with ... Hi Peter, There seems to be truth to what you say about the magnet rolling to the center of any given track --and then some...
The circular SMOT and the linear SMOT also use the phenomenon of gathering momentum. This is, I think, how magnets can be harnessed to do work. The difference...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the overunitybuilders group. File :...
overunitybuilders@yah...
Jun 2, 2006 2:29 pm
94
... the ... there ... of ... SMOT ... magnet ... saw ... slightly ... next ... be ... Hi Tom, I discovered something yesterday while experimenting that will...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the overunitybuilders group. File :...
overunitybuilders@yah...
Jun 5, 2006 12:43 am
97
I built the calloway motor with the magnets on the disc and the v's positioned on the outside as per the photo in the files section. I can say as is that it...
Yes, I considered making more uniform v's out of soft iron wire, matching the curvature of the outside of the disc. Much better than trying to align 30 nails...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the overunitybuilders group. File :...
overunitybuilders@yah...
Jun 6, 2006 2:55 am
100
Hi All, I am right now getting things together to make a movie clip of this track with the runner magnet in motion on a level surface. It will be an eye...
Hi, I'm not sure i understand the configuration of the magnets in this experiment but i'm sure the video will help explain it. Regarding the great work on the...
I know this will sound crude. A hammer works great. Use a block of wood next to the side of the speaker magnet and hit it hard, it will break off the cone...
The video shows the magnet rolling several feet after it leaves the influence of the staggered track. This is incredible! I wonder what would happen if the...
Hi all, it looks like I am going to have to start deleting the oldest files, as we are at 98% of capacity for the group, I will put them on a disk for storage...
... Hi Tom, I have been there and made that. It looks good in theory but does not work. At least for rectangular magnets formed into a circle. The outside...
Sphere magnet alignment: Regarding sphere magnets, can you provide alignment maintenance when the flexible tube they occupy is curved? I think the maintenance...
... when ... of ... short ... Also, ... at ... friction ... a ... and ... rails ... meet ... idea. ... gets ... to ... all, ... not ... to ... of ... other ......
This was also posted on free_energy, but serious experimenters in that group are few and far between, so I want to post this here too: I finally drilled out...
Alex, I have seen this somewhere before. When I look at it I wonder how the levitated steel ball (or sphere magnet) will want to fall. If the track magnets...
Tom, Looking at your magnetman JPGs posted in the files section: I think I can see how the magnet on the little car can be first attracted into the track, then...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
