I had at one time a set of books, I believe they came from someone in RI or Conn., that went over troubleshooting, flow charts, service etc. Does anyone have a...
By chance were the manuals from Gas Training and Development? ____________________________________________________ Start your day with Yahoo! - make it your...
INTERNATIONAL CAREER OPPORTUNITY Our client a Sub-contractor who are specialists in design,installation and maintenance of high-quality Refineries and Oil Gas...
If anyone knows of any experienced bobtail drivers and tank installers in the Ingham, Jackson, Livingston and Washtenaw counties area of Michigan have them...
Hello, Well, after five years in the propane business and two of them as petroleum department manager it is time for me to depart the business. As of August...
Best of luck Sam! Just Remember, You Can Take The Man Out Of The Propane Industry, But You Can't Propane Out of The Man! Who knows what tomorrow might bring....
I'm not going to be venturing too far. I'll still be here in this group and giving my two cents worth or some of my stories about my experiences in ...
Hey! You got luck. You are getting out young. Just kidding. Why did you leave the LP business? I have been a level 2 HVAC tech., self-employeed fuel oil...
Just wanted to say hello. I am still "wet behind the ears" in the propane business. I have been employed for almost 2 yrs with a propane company based out of...
There are many resons why I left the propane business and really none of them had to do with the propane industry itself. First and foremost was a better ...
Enter your vote today! A new poll has been created for the propane_gas_workers_group group: Does anyone think that employees should be allowed by the company...
propane_gas_workers_g...
Aug 6, 2005 2:41 am
853
Sorry for the late reply. No it is not the New CETP. It is a class the qualifies me to teach and train LP staff the CETP classes and I am a proxy for the...
Eagle Automation Corporation is an automation and control service company that is committed to excellence in the design and installation of automation systems...
The following propane_gas_workers_group poll is now closed. Here are the final results: POLL QUESTION: Does anyone think that employees should be allowed by...
propane_gas_workers_g...
Aug 20, 2005 8:02 am
856
Greetings everyone, My name is Loren and I work in the Philadephia area as a bobtail driver. We have two divisions in our company, which is approximately 75...
Greetings everyone, My name is Loren and I work in the Philadephia area as a bobtail driver. We have two divisions in our company, which is approximately 75...
I do it both ways depending on if dope is handy. Works fine either way. Although, I do seem to have less initial leaks if I use dope. David Boyd ... ...
hi everbody, i was taught never to use pipe dope on flair fittings because it can go and plug the copper line cutting down the flow.i have seen this happen...
I also have been taught 16 years ago that it is NO NEED TO APPLY pipe dope to flared fittings. I have never checked the books to confirm this either. I just do...
The only time I would use pipe dope was when the fitting was a pipe thread. Never used dope on flare fittings but I did find that if you use a GOOD flaring ...
To all, Thanks for the help. I'll still welcome more thoughts. But I am finding the consensus to be in favor of secure, burr-free flare fittings, rather ...
I have to chime in on this one. I know some of you will most likely hammer me after saying this, but however good your intentions are, using pipe dope on the...
I just wanted to take a moment to send our thoughts and prayers to all the people affected by this storm on behalf of the group. The cleanup efforts and the...
Mark, What you have is what I was taught, ( NEVER USE PIPE DOPE ON FLARED FITTINGS, ONLY DOPE THE MALE THREADS ) But was never explained to me of why! As the...
Blossman Gas was in the midst of the hurricane with at least 4 plants!!! I hope and pray that all my Blossman friends and families are ok and getting along the...
I am looking for help identifying propane industry members who were impacted by Hurricane Katrina, whether through damaged facilities or actively involved in...
Hi, I'm new to this group but, I've read several posts and I'm already impressed. This is a great resource for this industry. I'm looking for experienced...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
