Well... I installed 'ucon' on my machine and set up the software parameters. I turned on the device and the characters transmitted look like what you would get...
Thank you. ... Thank you. On 2012-05-04, at 6:51, Remi Bilodeau < remi.bilodeau@... > wrote: Use ucon software, Jason put the link on the instruction...
Thank you Jason. The device does prompt the boot loader prompt and does prompt XMODEM when the return is pressed. It also switches to run if the return is not...
I really should proofread my posts better! Let me try this again: Joseph, Ucon is a minimal terminal with excellent XMODEM capability. Â I'll run through the...
Joseph, Ucon is a minimal terminal with excellent XMODEM capability. Â I run through the steps: 1. Start of Ucon2. You'll be presented with a setup window....
Actually, I haven't updated the manual yet because I was waiting to update for the next firmware revision. Â In the meantime, here is a direct download link to...
Use ucon software, Jason put the link on the instruction manual. Envoyé via Galaxy S - Android ICS 4.0.4 ... Use ucon software, Jason put the link on the...
Greetings, I tried to update the firm ware of my Yagtracker from 1.40 to 1.44. I used TeraTerm to do the XMODEM transfer and it seemed to accept it OK. A...
i have been looking at the Microsat WX3IN1. Interesting device, something I've been looking for, for some time now. I read the owners manual and something that...
RPC Electronics, LLC is happy to announce they are now the sole US dealer for Microsat. Microsat is a small Polish company that has created some innovative...
We finally have MX145H modules back in stock and they are ready to ship out now. http://rpc-electronics.com/rf.php Thanks and please emails us with any...
Yes.... I work on this right now... Sampling rate will be different to remove the harmonic. Jason will release the fix when avalaible and tested. Expect a ...
will this be a new version of the cpu sofware? if so i am looking forward so i can use the yagtracker thanks very much!! wb4kdy On Wed, Mar 14, 2012 at 12:12...
I work on version with different sampling rate, to shift the carrier sometime present at 144.390Mhz Carrier is generated by codec at 12Khz sampling rate. PLL...
help I have tryed everything, shielding on cables and also added ferites, many differnce radios, there is just to much "RF" from the yagtracker box, if I lay...
It seems to be unmodulated carrier it ceases when the tracker is turned off it raises the noise floor by about 2-3 s-units while the tracker is on, it goes up...
it is a steady noise of unmodulated carrier ... From: Remi Bilodeau To: rpc-electronics@yahoogroups.com Sent: Monday, March 05, 2012 3:56 PM Subject: Re:...
When you say RF, this is noise burst, steady noise of unmodulated carrier ???? LCD refresh can cause some noise burst. (around 1 or 2 hz) To reduce noise,...
i think i will try shielding on my cabes and adding some ferites, I would like to use just the FT857 only in my car, but it gets to much RF from the...
i think i will try shielding on my cabes and adding some ferites, I would like to use just the FT857 only in my car, but it gets to much RF from the...
i adjusted the gain to 80% peak and i also had RF from the box, so on my FT857 i had to adjust the SQ so high that it was cuting off the packet signal. ... ...
Me and Jason have noticed some time a RF carrier near 144.390. Not always present. In next version I add a parameter to modify sampling rate (actually a 12Khz)...
I had to really take the time to adjust the audio in and out once its set it works great one thing I am noticing and it may be due to my wireing is that there...
