I purchased a 586 Engine Eval Kit recently for the sole purpose of running some complicated code involving transcendental functions on the math coprocessor. My...
I need a baud rate of 1Mbps for an application. RS-485 can support this data rate in theory, but does 586 Engine or any other controller support this rate? ...
Does anyone has done some code using the libraries provided by cogwheel? I need to receive, treat and send data using the udp protocol, but I donīt know how...
I'm using the ACore86 and looking at the step 2 instructions for downloading my firmware but I don't seem to have to L29_F400.HEX file you reference. Do you...
Hi All - Does anybody happen to have an electronic version of the old Tern software development manuals? My company purchased (several years ago) the...
I've completely confused myself concerning the memory usage on the AE-P board with 128K SRAM installed. Looking at the LOC file after a hex build I see that...
I was running through the test program fs_ser1.c to test my compact flash card as well as the PCMCIA Adapter. Both of these work great, but I'm having trouble...
I just purchased the FC40 EV-P kit and this is my first work with embedded system design. Can you suggest what would be a good thing to start with? Are there...
Hi, I'm looking at the Tern FlashCore system. I have a hard coded pic chip that is running a/d and some other things.. It is streaming data out of an rs-232...
Iīve changed my eprom content, and conected the serial 0 of my board to COM 1, and I set the baud rate to 57600 bps, sience my board has a 20MHz crystal. But...
On the A-Core86 we are currently using, I am attempting to use PIO-P3 (J2-15) port. This pin is also used as /PCS5/A1 by the processor. I can set this pin...
Group: I'm trying to use the PIO-P3 pin in a project but found some very strange behavior. I set this pin up as a PIO-INPUT but when I look at the pin with a...
I'm developing a measurement system using two A-Core 86 boards connected via serial port 1. I've allocated a 4kB receive buffer on both ends and have the baud...
The following text is written in the tern site: "Now, the TERN filesystem can also be directly accessed through the serial port without requiring the rest of...
Hi, I have an A-core86 board and I canīt make it work with Paradigm C++ tern edition for windows. I was using Borland C++ for DOS, and it worked perfeclty. I...
I need to open a file on a compact flash card, write data to the file then write data to the first 8 byte locations of the file before closing. I need...
I purchased the ethernet memcard. DO you have any suggestions on how I can get a little http server up and running? Can you point me in the direction for the...
I was interested in using one of tern's controllers to prototype my application for a specific type of process monitor. Specifically in the application, I...
I don't see sample code posted to this group. I think it would be very helpful to have some additional code samples beyond what is supplied with the CDROM from...
Hi, I am having problems going inot step 2 mode (sram standalone) on an A104 board. I can run the unit step 1 mode without a problem. When I disconnect power,...
I recently read at "http://www.amd.com/epd/processors/2.16bitcont/2.am186exfa/6.am186e s/index.html" that the 188ES processor is no longer available. The ...
I've go an urgent question. I am using the A104 pcb. I am having problems with the debug operation. Everything was working fine and then I seemed to lose the...
Doing some additional investigating ... Someting in my application causes the Break Detect bits in the SP1STS (Offset 12h) control register to become set -...
Hello all. I did some further tests on the problem I'm having with sending data to the Serial 1 port. As stated before, the SCC port, when swapped with the...
I'm developing a product that will incorporate the usage of a TD-40. I Purchased the TD-40 EVAL kit thinking that I could "figure" it out, but I can't! Would...
I've got an application that negotiates a PPP (Point to Point Protocol) link and I've run into a snag with the TD40. It seems that whatever routine that places...
Thanks for bringing that to our attention; that's a new one. We've had issues where Hyperterminal was strangely slow, on both NT 4.0/Windows 2000 machines......
