Looking for a tool to borrow, rent, or buy. Thomas and Betts Co. WT-157 or WT-157N. Please respond to: Tom Colella Vermillion, Inc. ...
Tom Colella
tcolella@...
Jan 4, 2007 8:59 pm
2020
Tyco connector part numbers below are needed: 1. 6-962915-6 2. 963904-3 Sam Yankelevitch Prettl Electric Corp. Greenville, SC (864) 220 1010 ext 145 ...
Sam Yankelevitch
s.yankelevitch@...
Jan 10, 2007 7:29 pm
2021
Does anyone have 50 or so of these terminals they would sell me? I am in critical need of at least 10. Any help would be greatly appreciated. Dave Souders ...
Dave Souders
dsouders@...
Jan 13, 2007 5:32 pm
2022
Does anyone have an applicator for this terminal? I am in desperate need of 100 8" circuits. I have seals, terminals, but can not seem to locate an...
I'm trying to source a bit of a special battery cable lug and was wondering if anyone had suggestions on where to look. My customer requires a crimpable...
Hello everyone, We are looking for a machine that can print on both sides of shrink tubing and are wondering what everyone else is doing? We'd prefer a...
Dan Snyder
dan.snyder@...
Jan 24, 2007 10:09 pm
2028
Hello! I am working with a customer who is using a mica tape wire with glass braid (MGT) for high temperature applications. The temp requirement is 425C....
Hello Peter - How quickly could you provide 140 each Amphenol # RJFTV7PEM1G ruggedized RJ circular connector with dust caps # RJFTVC7G? Thanks, Michael Strawn...
Hello everyone, I'm looking for ~50 pcs of Tyco 66588-1 or 66588-2. I believe it is an obsolete part, but I'm trying to help out a customer's service...
Kenny, I found a company that has 66588-1 in stock. Aesco Electronics, Inc. 330-245-2630 Also, one that has 66588-2 in stock Lectronix Plus/Bus Ind. ...
Hello all We have been looking for an old packard connector 12034251, and Pioneer has not stock. I has since been replaced by 12186339 and more recently...
Would you please share your experience with your current operation system for your computer? We have been using Manex and it needs to be updated. Before we...
Judy Wilson
judyw@...
Jan 29, 2007 11:39 pm
2037
Judy, We use Visual Enterprise and it's a great ERP system. Not too expensive, ($50K), quite flexible, very, very good in financials, excellent manufacturing....
Hi Judy. Data Cable also uses Visual and we find it to be a good fit for our application. It is very flexible and works well in a mixed manufacturing...
We have been using Navision Manufacturing software for the past 4 years. Our expeience has been less then satisfactory partially due to bad implementation and...
We have been using Avista (Navision) since 1997. We chose it because we wanted character based input screens that would run under SCO Unix on dumb terminals....
Judy, In May 2004 I posted a message to this list asking what ERP packages everyone was using because we were starting a search to replace our old ...
Dan Snyder
dan.snyder@...
Feb 1, 2007 5:47 pm
2042
Thanks to all of you for your input. This is what makes WHMA so great! Judy Wilson ... <http://www.epicor.com/www/products/manufacturing/vantage/> ... ...
Judy Wilson
judyw@...
Feb 1, 2007 6:00 pm
2043
Greetings, We have a Kappa 220 which is being "fed" from a barrel of 14 AWG wire. I have noticed when printing with our inkjet marker, a fuzzy build-up at the...
Neil, R. Stuart
rsneil@...
Feb 2, 2007 9:13 pm
2044
What kind of ink jet printer are you using? We have komax gamma's with wiedenbach 201's and 207's and have similar issues occaisonally. Dwayne Waterman ...
Waterman, Dwayne SEA
dwayne.waterman@...
Feb 2, 2007 9:22 pm
2045
Our printer is an IMS 291 ________________________________ From: whma@yahoogroups.com [mailto:whma@yahoogroups.com] On Behalf Of Waterman, Dwayne SEA Sent:...
Neil, R. Stuart
rsneil@...
Feb 5, 2007 11:48 am
2046
Sounds like static build up from the insulation rubbing the plastic pulleys. Do you folks have any of the air ionizers for neutralizing static charge? Try...
cstrjnl@...
Feb 6, 2007 12:18 am
2047
I never had any luck with ionizers but maybe you will. Try a clothpin with some felt in the pinch area. Simple and easy but you may need to replace the felt...
Does anyone out there know of a source of information for minimum tensile strength for wire. I'm not talking about crimped connections, but for the actual...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
