Hi everyone! I need 30 wires crimped with a JST SSH-003T-PO.2. I can supply the wires and contacts. Can anyone help me? I'll even pay! :-) (If I have to!)...
Randy
randy@...
Jun 6, 2007 8:21 pm
2144
I am looking for a method to strip oval shaped cloth covered thermocouple wire. Does anyone have any ideas? Thanks....
We are looking for a Manufacturing Engineer, perhaps two, who has experience in the Harness business. We offer a competitive salary, good benefits and a great...
Hastings
hastings@...
Jun 12, 2007 2:07 pm
2146
We are looking for an electrical engineer/quality mgr. Experience in wiring harnessing is preferred. We offer excellent benefits and a great location about 20...
Anyone know where to get a fixture that will hold a P5 connector during plugging/assembly to prevent splaying? All help/suggestions appreciated. ... Ready for...
Anyone know where to get a fixture for a P5 connector to use during plugging to prevent splaying? ... Park yourself in front of a world of choices in...
Hello everyone: I'm fairly new on the Harnesses business ,and I'm looking for a full automatic machine that can cut, strip and crimp, automatically. I'm the...
Dean, Not making any promise of success, but if you can send me a sample of the wire, I will try what I have in mind, and report back to you, Dave... Dave...
Dave Kelly
davek@...
Jun 14, 2007 9:22 pm
2153
Hi Dean, Using a laser to strip non round wires is a great way to strip wires without damage to the conductor. Also with cloth type insulations the laser will...
Take a look at the Schleuniger CC63 crimp center. Processing time is rated faster, and it is pretty easy to set up. It's a good machine for entry into wire...
I would have to agree With Dean support is great from Schleuniger. They will supply you with all the videos on their machines which also helps They also have...
Hello Everyone, I have been looking for an off the shelf software program for tracking employee productivity in a job shop. Most of the programs that I find...
Brian Rohs
brian@...
Jun 18, 2007 2:28 pm
2157
Brian: How about developing your own excel spreadsheet that calculates a dollar per hour productivity measure based on the number of dollars shipped divided by...
Brian, I'm not sure that you'll find much to integrate with QuickBooks. I know there are lots of standalone solutions out there as I get junk mail from ...
Dan Snyder
dan.snyder@...
Jun 18, 2007 5:21 pm
2159
Hello Brian, i have been using a company for the past eleven years for production history tracking. we are using a bar-code with a serial number to track all...
Thanks for your inputs..!! I'll keep looking for a little while before take the final decision Saludos y Gracias Catresi ... Schleuniger. ... also helps ... ...
Bill, Thank you for the suggestion, I'm going to try that out. It sounds like we are in the same business. So you probably have a split between labor only ...
Brian Rohs
brian@...
Jun 19, 2007 4:54 pm
2162
Brian: We use total dollars shipped and we used three years of past data to generate our baseline starting point for the gainsharing program. But whether or...
It worked for me last time so here I am again! I would like to borrow, rent, buy a JST applicator for Terminal # SIN-21T-1.8S. The applicator # is CMKSL, die...
Randy
randy@...
Jun 22, 2007 4:15 pm
2164
I was wondering if anyone out there has had any experience with hot stamp marking directly on silicone insulation (not on braided fiberglass) with any success?...
You may wish to look at Megomat UNO as well as the Schleuniger Crimpcenter series. In my opinion, they are probably the two best machines currently available....
Our Komax Model 33 programmable cutter and stripper is in need of repair to the tune of roughly $2,000.00 Can anyone recommend a replacement for it, Komax or...
Hi Tom, we really like our Schleunger. We have had very good experience with all of their equipment. Check out the Wiring Harness News classified for used ...
Judy Wilson
judyw@...
Jun 29, 2007 8:29 pm
2168
We have 400pcs of a Conxall p/n 7382-4SG-300 we would like to get rid of. Are you interested?? Please respond with your bid. Thank you LeAnna R. Armstrong ...
Can anyone reccommend a manufacturer for standard racks suitable for holding 24" flanged terminal reels? I can't seem to find anything off the shelf that fits...
Hello group, can anybody recommend a manufacturer who carries a system of modular /composable fuse/relay holders? thanks! HORACIO GUTMAN CONECTECH S.A. Panama...
Olen poissa toimistosta alkaen 05/07/2007 ja palaan 06/08/2007. Vastaan palattuani. This e-mail is intended only for the individual or entity to which it is ...
juhani.pelttari@...
Jul 4, 2007 9:25 pm
2172
Hello All, Can anyone supply me with some Molex parts? I require the following ASAP for some Prototypes 34566-0303 qty 3 31381-1000 qty 2 31382-1001 qty 2 ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
