We have recently finished our physical inventory and are looking for any best practices out there for estimating wire on hand, i.e.the amount of wire on a...
I had heard about a hand device that would calculate the lenght once plugged on to the ends of the wire based on the impedence....and it was very accurate. The...
THis is a good topic. I have always weigh counted wire. THis is more of an art than a science. I am intriqued by the device that measures wire by its...
Both UEI and Etcon sell a "cable length meter". We purchased the CLM100 from UEI. Simple to use and fairly accurate, mfg claim is +/- 1% on lengths over 300'....
If you have access to both ends of the wire (i.e. on a reel) you can do this with an ohm meter as follows. Measure the resistance of the reel of wire. Next...
Remember that the resistance value of the wire is based at a specific temperature. (65 F?) If the spool is at a significantly different temperature, the ...
cstrjnl@...
Jan 5, 2008 6:33 pm
2273
We have used LADD as a distributor of Deutsch parts and as we review our supply chain we are looking for additional distribuotrs of DEUTSCH parts. Can anyone...
I believe that LADD is the only authorized distributor of Deutsch parts in the US. Fran Sabol Materials Manager Pacer Marine Group/JMS Wire 1555 Apex Road ...
Try Wes-Garde, they sell Deutsch, though they probably buy it from Ladd and resell. You can try Cantwell-Cullen in Canada, though they may not be allowed to...
You can purchase from Deutsch direct if you are a large enough company but you have to put up with their 30 day plus or minus schedule and quantity orders....
wE ARE LOOKING TO PURCHASE A VERY SMALL AMOUNT OF THE FOLLOWING AND WANT TO AVOID A LARGE MINIMUM BUY IF AT ALL POSSIBLE. WE NEED: 10 FEET EACH OF A APLHA...
I'm looking for two- Dynalab 256XL circuit testers. Does anyone have units to sell? Thanks, Bill Harwood Precision Cable Assemblies, LLC 16830 Pheasant Dr. ...
Bill Harwood
billharwood@...
Jan 16, 2008 5:14 pm
2280
We are looking for Hitachi Automotive/rv connector distributers. Does anyone have any insite as to who might carry the line? Thanks...
Terminal I need to hand crimp is Delphi 12020801-L Delphi is not getting back to me so I don't know their respective tooling part number(s) Power & Signal has...
Tom, Have you been able to resolve this? If not, I have a spare P&S frame I could loan you for a week or two. I don't have the die set, only the hand tool...
Dear All, does anyone know of a source with reasonable prices and quantities for Bosch components (terminals and connectors)? I am looking for: 1 928 404 195 1...
Does anyone have a GOOD rep/dist/source for Lemo Connectors?? Thanks and see you in Florida in a couple of weeks I hope! Randy L. Olson, General Manager, ...
Randy
randy@...
Jan 30, 2008 6:55 pm
2286
We buy direct. LEMO USA (408) 955-1155 Alan _____ From: whma@yahoogroups.com [mailto:whma@yahoogroups.com] On Behalf Of Randy Sent: Wednesday, January 30, 2008...
Thanks Smiley! I appreciate the info! +randy From: whma@yahoogroups.com [mailto:whma@yahoogroups.com] On Behalf Of Smiley Tran Sent: Wednesday, January 30,...
Randy
randy@...
Jan 30, 2008 8:58 pm
2289
Hello, my name is Al Da Valle and I am manager of supplier engineering for Aviza Technology. Judy Wilson invited me to the WHMA web site. The new NFPA 79...
Does anyone have up to 1000 pcs of Yazaki 7116-4103-02 that they could spare (to sell, or could be replaced). My delivery has been pushed back from mid...
Try www.smdinc.com <http://www.smdinc.com/> They show 90000 in stock in Ca. Thanks, Larry Greco, Buyer Atlantic Teleconnect, Inc. 2529 Commerce Parkway North...
I will be out of the office starting 02/12/2008 and will not return until 02/18/2008. I will respond to your message when I return. mailgatemia2 made the...
Hi All, I would like to know if anyone has done the pull test for 1/0AWG wire before and really like to share the information how we done it and what type of ...
Does anyone know if here are some Harness Industry Specific recruiters out there or even some Electronics Industry Specific ones. We have a couple of higher...
Hastings
hastings@...
Feb 15, 2008 9:51 pm
2296
Good afternoon everyone. I hope everyone is getting a good start to the year. We are trying to do a little spring cleaning and as a result we have identified...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
