Hi Dave: I've asked the web designer on our end to create a buyer search feature including mfg. and part #. Should be done and online by end of next week. Hope...
jrmanke@...
May 2, 2004 1:11 pm
792
That would be great. One group is only putting their part number on some items, so all I can find out is that it is Packard. Mfg p/n are a great thing to...
Hello all, I'm the IT Manager at Mercury Electronics. We build-to-order cables and wiring harnesses the same as most of you. We are starting a project to ...
Dan Snyder
dan.snyder@...
May 3, 2004 2:11 pm
794
Help I urgently need the following Yazaki Parts if anyone can help 7116-4660-02 Terminal (sumitomo number 1410-0526) at least 1 reel 7222-7444-40 ...
Hello WHMA members Unfortunatly we can not help with these Yazaki parts. **** But I also need help!!!! ***** As, we have the worst experience with the Yazaki...
I spoke with the samples coordinator at Yazaki NA and said that it's a lot easier to get samples from Packard and Tyco than it is Yazaki and he agreed. It's...
I fully agree, but with asia becoming a major player....if we want to service some large corporations (i.e. Komatsu, Hitachi, Toyota, etc.) for which some of...
While we are not a distributor for Yazaki (yet), we do buy directly from them out here in Asia. Believe me, the buying experience is as wonderful for us as for...
To all, I have a need for a tooling person that is very knowledgeable in AMP and Molex crimping machines and applicators? Anybody know of someone in the San...
Bob McAniff
b_mcaniff@...
May 5, 2004 3:43 pm
801
Bob, when you find someone that will work cheap and does not want to live in California, please forward their resume to me. Sandy Brown Elec-Tec, Inc...
Sandra Brown
elec-tec@...
May 5, 2004 3:45 pm
802
I see that there is now a search engine for the Excess Inventory page, but did all the entries get removed? Also, need to make sure that when companies list...
Have you tried contacting any of the big Tier I harness outfits in the US and Mexico? Sometimes they are willing to sell these components to us "smaller"...
I have had to deal with Yazaki in Texas for some Marine customers. They were quite adamant about the fact that "they don't deal through distribution" - made...
Is it safe for me to start poting my excess inventory? If not, when should I check back on the status of updating the page? Sandy Brown...
Sandra Brown
elec-tec@...
May 6, 2004 10:53 pm
806
Hi folks, Have been trying to locate this company but with little or no success. If anyone can help, please email me privately. Thanks, Lyle Pai AIDA...
Hi folks, I've got an urgent requirement for PED(?) wiring P/N SP015679. If you have inventory and can spare some, please contact me. Thanks and regards, Lyle...
Dear Lyle Pai : Good Day ! Can you provided detail harness drawing ? Thank You ! Mr Te Peng Seng Tsujimoto (M) Corporation Sdn Bhd (Malaysia) ... From: "Lyle...
Tsujimoto (M) Corpn. ...
tsu18@...
May 14, 2004 3:59 am
809
Does anyone know if there is a jacket material that can be rated at 450 degrees C? It also must be impervious to oil. Any help will be appreciated....
Judy Wilson
judyw@...
May 14, 2004 7:07 pm
810
Does any one have a pneumatic crimp tool # 13640 and T & B Die Set GS590 that we could possibly rent? Tom Tarasewich Electronic Connectors Inc 125 South 5th...
Judy, Are you sure 450 C??? Sounds unreasonable, over 800 F. If you're looking for jacketing to 450 F, perhaps I can help. Have you considered polyester...
I just was reading about this wire the other day. You might try Specialty Cable Corp. They list on their website that they have a wire/cable that can go to...
Thanks Dave, I'll check it out. ... From: Dave McCloskey [mailto:davemc@...] Sent: Friday, May 14, 2004 1:22 PM To: 'whma@yahoogroups.com' ...
Judy Wilson
judyw@...
May 14, 2004 8:56 pm
814
Judy, This was mentioned to me by our Engineer...Kapton is made by Dupont and it is used as insulation for cables as well...we do not know who would extrude or...
Mark O'Donnell
marko@...
May 14, 2004 9:32 pm
815
Hello all, Unfortunately, I only had 3 responses. Thank you Sandra Brown, Al Macintyre and Judy Wilson Shepherd. Below, I've included a summary of their...
Dan Snyder
dan.snyder@...
May 17, 2004 5:18 pm
816
Can anyone offer up an effective means of mating conductors for 30ga wire to a 26ga or 24ga wire. I've got a customer that has been attempting to solder but...
Autosplice is the ticket. go to www.autosplice.com ... From: "Steve Pilipchuk" <steve.pilipchuk@...> To: "Whma@Yahoogroups. Com"...
chuckr@...
May 19, 2004 4:31 pm
818
You are correct!!! ... From: chuckr@... [mailto:chuckr@...] Sent: Wednesday, May 19, 2004 9:32 AM To: whma@yahoogroups.com Subject: Re: [WHMA]...
Bob McAniff
b_mcaniff@...
May 19, 2004 4:58 pm
819
Seeking Acquisitions of EMS, CEM / BOX BUILD / Cable Assembly Mfg. Firms We are a large wire, cable and Interconnect distribution company who also owns two (2)...
We are looking for some 18/2 and 18/5 GXL cable with a gray jacket in small quantities. Does anyone out there stock such a thing? Can anyone recommend a source...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
