Hi all..... Anyone have a Komax 35 or Kodera C350 they want to send to a GOOD home with Squires Electronics???? Might be interested in more than 1..... Please...
Randy Olson
randy@...
Oct 5, 2004 9:52 pm
998
Has anyone had experience with bar code printers that both print the bar code and then verify what was printed? Also, we are looking to print in languages...
hello, we are producer for test holders and accessories as pneumatic test holders, production boards etc. for harness producer we are working for Delphi,...
Murat ERKUL
muraterkul@...
Oct 6, 2004 11:16 am
1000
Does anyone have any Amp 170104-2 terminals? We have an URGENT need--from 1000 to 12,000+. Thanks, Cliff Cochran Automatic Coax & Cable 4060 St Johns Parkway ...
In search of about 50' of 28 ga UL 1213 in White. If you have any you can spare, please give me a call. Best regards, Dave McCloskey Electrical Engineer TM...
Does anyone have connector number MS17348R24C10S.We need 23 toatal OR just 3 pcs will tide us over.Thanks Tom Tarasewich Electronic Connectors Inc 125 South...
Does anyone know of a good manf supervisor from a shop that had to close down? We would like to find one sooner than later. Your input and direction would be...
Gary Martinet
gary@...
Oct 18, 2004 7:16 pm
1004
Sorry everyone, Jack Crawford mentioned that it sounded like I may be looking for someone to close down a shop. I just wanted to be clear - we are growing...
Gary Martinet
gary@...
Oct 18, 2004 8:16 pm
1005
Please give me a call. I'd like to get some more details on what you need. I may have a solution for you. Thanks. Kim Johnson 320-679-0512 Cell 612-390-0623...
One of the necessary non-value add activities we have is the creation of process instructions for Production. Being predominately in the cable side of the...
We are looking for a Schleuniger HS4140 hot stamp machine. If anyone has one they would be willing to part with, I would appreciate a response. Thanks! ...
We are also looking for any software that anyone may be aware of to assist with the quoting (costing) process and setting up of documentation (cut-lists, etc.)...
HI WHMA Members: We received this request for information on the WHMA website - can any Suppliers out there help Mr. Ross? If so, please contact him directly...
jrmanke@...
Oct 19, 2004 8:05 pm
1010
Komax has the ZETA machine that can cut / strip / seal / terminate / solder dip / ink jet / block load. Block load is referred to as "loading a connector with...
Our factory order paperwork prints process instructions on the paperwork. However, the time for engineers to key in the information is apparently not cost...
When I was on the WHMA software committee a few years ago, I learned that there is excellent software for each of several islands of computing, each of which...
It is interesting you should say process instructions. Once you have some, shouldn't you be able to reuse these as needed and therefore reduce your time that...
This subject has been around for a long time and as far as I know...there is no one out there who has come up with a "canned" solution for companies in our...
Mark O'Donnell
marko@...
Oct 20, 2004 3:02 pm
1016
Has anyone else looked at the Harnware system? It fits in with VISIO, which can be used to draw "to scale" layouts. According to the website, looks like it...
Hello to all our colleagues in the group from sunny England! On the subject of harness design, manufacture, layout and circuit software please look at Vesys...
Dave- I've looked at it and it doesn't on the surface look too bad...but it doesn't address all the needs this forum is looking for as being a complete...
Mark O'Donnell
marko@...
Oct 20, 2004 3:58 pm
1019
Thanks for the input - Rich I was just wondering. Don't have the time on my hands, but interesting still....
Does anyone have the capability to process "small" coax (not quite "micro-coax" but close). BELDEN 83265 (RG-178B/U 50 OHM COAX) It has an O.D. of approx....
Dave, This is an old message, so I trust you were able to get the parts you were looking for in the message below. However, if you need anything in the...
Does anyone have an extra copy of a CS-9 manual they can part with? (Spanish or English) Thanks in advance for any consideration, Wallace Electronics Steve...
Steve - we have a CS-9 manual left over from a machine that we probably sold a decade ago. I would be happy to send it to you for free. Should I use the ...
We have excess inventory (10,000 pcs) of part # SQHG 8 OHM 10 WATT resistor with a hole diameter of .162 if anyone is interested please make an offer. ...
Would anyone be so kind to see if they have the manual for a Eubanks 9200 wire stripper and if so we would Love to purchase a copy from you. Thanks!! Mark A....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
